167658
20
Zoom out
Zoom in
Previous page
1/24
Next page
18
20
Connect RCA outputs (CH1/2
and CH3/4) of the head unit with
LINE INPUT (CH1/2 and CH3/4)
of the amplifier.
Subwoofer 2
4 - 8 Ohm
X-Over-Switch (CH1/2 Subwoofer 1 & CH3/4 Subwoofer 2)
• By using the Mono/Subwoofer-mode, switch to the LP/BP-position (LOW PASS/BAND PASS), that the higher frequencies are
cut off. The cut-off frequency should be between 60Hz - 100Hz. Adjust the level with the LO PASS-controller. In LP/BP-Mode
the Highpass-controller (HI PASS) is working also as Subsonic-Filter. The Subsonic frequency should be between 15Hz - 40Hz,
depending on the size of the installed subwoofer.
Input Level (CH1/2 Subwoofer 1 & CH3/4 Subwoofer 2)
• Turn the LEVEL control of the amplifier to 6V position.
• Turn the head unit volume control to about 80 - 90% of its full setting.
• Turn the LEVEL control clockwise until you hear some distortion.
• Then turn back the LEVEL control slightly until you can hear a clean sound.
Bass EQ (CH1/2 Subwoofer 1 & CH3/4 Subwoofer 2)
• This Controller regulates the Bass Boost from 0 - 18 dB.
Caution! Please use the Bass-EQ carefully. The additional boost may result in clipping or overload.
Bass Remote (CH3/4 Subwoofer 2)
• The provided Bass Remote regulates the Bass Level of CH3/4 from e.g. the driver's seat.
Bass Remote Control -
Connection for remote
control. This Contoller
regulates the Bass Level
from f.i. the driver's seat.
Speaker & RCA Connections
ZXi 4400 / ZXi 6400 / ZXi 9400
3-Channel-Mode 2 Mono Subwoofer bridged
RCA & Speaker wiring:
• Connect the LINE INPUT of the amplifier to the head unit line output with appropriate good quality RCA cables.
• Connect the speakers/subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT/ - CH1/2 - Mono bridged +
and the subwoofer with CH3/4 - Mono bridged +) of the amplifier.
• The minimum final subwoofer impedance must not be lower than 4 Ohms per channelpair. Too low speaker loads result in too
high heat dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal
Caution!
Do not connect speaker (-) to the ground or vehicle's chassis.
ZXi 4400 MkII
4 x 150 Watts
e13
021584
FUSE
GND REM BATT+ 12V
POWER INPUT
SPEAKER OUTPUT
+ CH3 + CH4
+ MONO BRIDGED –
+ CH1 + CH2
Subwoofer 1
4 - 8 Ohm
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics zxi 9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics zxi 9000 in the language / languages: English, German as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info