168839
16
Zoom out
Zoom in
Previous page
1/20
Next page
Speaker & RCA Connections
TXi 1700
Subwoofer with Dual-Voice-Coil 2 Subwoofers with Single-Voice-Coil
Subwoofer with Single-V
oice-Coil 1 - 8 Ohms
Subw
ofer w
th D
al-Voic
oi 1 - 8 Oh
s per V
oi
e-Co lo
i u
e-C
l m c
i
SET-UP MASTER-Amp
MODE - Schalter
• Switch to the "LP or FULL”-position.
PHASE
FREQ RANGE
Q-Control
SUB BOOST
BASS REMOTE
SUB SONIC
LOW PASS
LEVEL
Attend regarding notes on page 14 if you use
LOW PASS-MODE or on page 15 if you
use FULL-MODE.
Caution!
Do not connect speaker (-) to the ground or vehicle's chassis.
MASTER/SLAVE-MODE / Subwoofer-Mode with two Ampifiers
• Connect the "LINE IN" (L & R) of the MASTER-amplifier to the head unit´s line output with appropriate good quality RCA cables.
• Connect the "SLAVE OUT" RCA Output of the MASTER-Amp with the "LINE IN" RCA Input of the SLAVE-AMP.
• Connect the "REMOTE"-Terminal of the MASTER-Amp with the supplied BASS REMOTE.
• Connect the "REMOTE"-Wire of your head unit with the REM-Terminals of both Amplifiers.
• Connect the subwoofer with appropriate wires to the terminal block (SPEAKER OUTPUT - and +) of both amplifiers. As optional feature an
additonal Subwoofer can be connected to the non-occupied terminals.
• Connect the Protect/Bridge Connection of the Master with the Protect/Bridge Connection of the Slave.
This connection warrants if there is an operation fault both amps, Master and Slave, would go into protection mode so the amps are prevented
for any possible damages.
• The minimum final subwoofer impedance must not be lower than 2 Ohms in total (1 Ohm for each Amplifier) or 2 Ohms bridged. Too low speaker
loads result in too high heat dissipation and may cause the amplifier run into protection.
• Please observe correct speaker channels and polarity as printed by the speaker terminal.
SET-UP SLAVE-Amp
MODE - Switch
• Switch to the "SLAVE”-position.
PHASE
FREQ RANGE
Q-Control
SUB BOOST
BASS REMOTE
SUB SONIC
LOW PASS
LEVEL
All controllers are in this operation mode without function.
Only the output signal of the Master-Amp will be amplified.
MASTER
SLAVE
0dB 18dB
Connect Master´s Protect/Bridge
with Slave´s Protect/Bridge
Subwoofer
1 - 8 Ohm
Bass Remote Control - connection for remote control.
This contoller regulates the bass level from e.g. the driver's seat.
+
-
+
-
SPEAKER OUTPUT
MASTER
SPEAKER OUTPUT
SLAVE
SPEAKER OUTPUT
MASTER
SPEAKER OUTPUT
SLAVE
+
-
+
-
h
i
.Caution: Please observe t e r ght polarity
. Slave´s - to Loudspeaker´s + and Slave´s
+ to Loudspeaker´s -
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hifonics txi 1700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hifonics txi 1700 in the language / languages: English, German as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info