665945
2
Zoom out
Zoom in
Previous page
1/12
Next page
SLOGBD
HR
Sender Batterieinstallation
Der Sender wird durch eine 3 Volt
Lithium CR2032 Batterie betrieben,
welche im Lieferumfang enthalten
und bereits eingelegt ist.
Entfernen Sie lediglich die Schutz-
folie, welche seitlich aus dem
Sender herausschaut, so dass ein
elektrischer Kontakt hergestellt wird.
Um die Batterie zu wechseln,
entfernen Sie zunächst das
Namensschild auf der Vorderseite
des Senders und lösen die
Schraube. Entfernen Sie dann die
Rückseite des Senders durch
vorsichtiges Eindrücken des Riegels
mit einem kleinen, schmalen
Schraubendreher.
Tauschen Sie die alte Batterie aus.
Überprüfen Sie, ob die Batterie
gemäß der angegebenen Polarität
(+ = oben) richtig eingelegt ist.
Setzen Sie die Rück- und Vorder-
seite des Senders wieder
zusammen. Der Sender ist nun
betriebsbereit.
Empfänger Batterieinstallation
Schieben Sie die Batteriefach-
abdeckung auf der Rückseite nach
unten und legen Sie die Batterien
ein (nicht im Lieferumfang enthalten)
2 x 1,5 Volt LR14 / Baby. Beim
Einlegen bitte auf Polarität achten!
Schieben Sie die Batteriefach-
abdeckung des Empfängers wieder
ein. Der Empfänger ist
nun betriebsbereit.
Sender Befestigung
Sie können die beiden Löcher
auf der Rückseite des Senders als
Schablone verwenden, um
die Bohrlöcher zu markieren. Die
passenden Dübel und Schrauben
sind im Lieferumfang enthalten.
Transmitter Battery Installation
The transmitter is operated by
a 3 Volt Lithium CR2032 battery,
which is included in delivery
and is pre-installed inside the
transmitter.
Just remove the protective foil
sticking out from the side of
transmitter, which will establish
the electrical contact.
To change the batteries, first remove
the nameplate on the front of the
transmitter and unscrew the screw.
Then remove the back of the
transmitter by carefully pushing in
the latch with a small, thin
screwdriver.
Replace the old battery.
Please check if the battery is
inserted correctly according to the
polarity (+ = up).
Reassemble the back and front
of the transmitter. The transmitter
is now ready for operation.
Receiver Battery Installation
Push down the battery cover on
back and insert batteries (not
included in delivery) 2 x 1,5 Volt
LR14 / Baby
. Please mind the
polarity! Push the battery cover
of the receiver back into position.
The receiver is now ready for
operation.
Mounting the Transmitter
Both pre-cut holes on the back of
transmitter can be used as
a template to mark the drilling
holes. The respective wall-plugs
and screws are included in
delivery.
Instalacija baterije oddajnika
Oddajnik poganja 3 voltna litijeva
baterija CR2032, ki je vsebovana
v obsegu dobave in že vložena.
Odstranite samo zaščitno folijo,
ki ob strani gleda ven iz
oddajnika, tako da se vzpostavi
električni kontakt.
Za menjavanje baterije najprej
odstranite ploščico za ime na
sprednji strani oddajnika in
odvijte vijak. Nato odstranite
hrbtno stran oddajnika, tako da
zapah previdno potisnete noter
s pomočjo majhnega, ozkega
izvijača.
Staro baterijo zamenjajte.
Prekontrolirajte, ali je baterija v
skladu z navedeno polarizacijo
(+ = zgoraj) pravilno vstavljena.
Hrbtno in sprednjo stran
oddajnika zopet sestavite.
Oddajnik je sedaj j pripravljen
za uporabo.
Instalacija baterije sprejemnika
Pokrov predalčka za bateriji na
hrbtni strani potisnite navzdol in
vložite bateriji (nista vsebovani v
obsegu dobave) 2 x 1,5 voltna
LR14 / Baby
. Pri vlaganju pazite
na polarizacijo! Pokrov
predalčka za bateriji
sprejemnika zopet potisnite
noter. Sprejemnik je sedaj
pripravljen za uporabo.
Pritrditev oddajnika
Obe luknji na hrbtni strani
oddajnika lahko uporabite kot
šablono za označevanje vrtin.
Ustrezni zatiči in vijaki so
vsebovani v obsegu dobave.
Ugradnja baterija u odašiljač
Odašiljač pokreće 3-voltna
litijeva CR2032 baterija koja je
obuhvaćena isporukom i već je
umetnuta. Samo uklonite
zaštitnu foliju koja bočno strši iz
odašiljača kako biste uspostavili
električni kontakt.
Za zamjenu baterije najprije
uklonite pločicu s imenom na
prednjoj strani odašiljača, a
potom otpustite vijak. Potom
skinite stražnju stranu odašiljača
oprezno utiskujući zasun
malenim, uskim odvijačem.
Zamijenite staru bateriju.
Provjerite je li baterija pravilno
umetnuta u skladu s navedenim
polaritetom (+ = gore).
Ponovno sastavite stražnju i
prednju stranu odašiljača.
Odašiljač je sada spreman za
rad.
Ugradnja baterija u prijemnik
Potisnite pokrov pretinca za
baterije na stražnjoj strani
nadolje i umetnite baterije (nisu
obuhvaćene isporukom) 2 x
1,5 V
LR14 / Baby
. Pri umetanju
pazite na polaritet! Ponovno
utisnite pokrov pretinca za
baterije na prijemniku. Prijemnik
je sada spreman za rad.
Pričvršćivanje odašiljača
Obje rupe na stražnjoj strani
odašiljača možete koristiti kao
šablonu za označavanje rupa za
bušenje. Prikladni moždanici i
vijci priloženi su.
“C”, LR14
“C”, LR14
Mode
Code
Setting
Switch
Volume
2
1
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Heidemann 70842 - HX Trendline at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Heidemann 70842 - HX Trendline in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Heidemann 70842 - HX Trendline

Heidemann 70842 - HX Trendline User Manual - German, Dutch, French, Italian - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info