665937
3
Zoom out
Zoom in
Previous page
1/12
Next page
Sender Batterieinstallation
Der Sender wird durch eine 3 Volt
Lithium CR2032 Batterie betrieben,
welche im Lieferumfang enthalten
und bereits eingelegt ist. Entfernen
Sie lediglich die Schutzfolie, welche
seitlich aus dem Sender herausschaut,
so dass ein elektrischer Kontakt
hergestellt wird.
Um die Batterie zu wechseln,
entfernen Sie zunächst das
Namensschild auf der Vorderseite des
Senders und lösen die Schraube.
Entfernen Sie dann die Rück-
seite des Senders durch vorsichtiges
Eindrücken des Riegels mit einem
kleinen, schmalen Schraubendreher.
Tauschen Sie die alte Batterie aus.
Überprüfen Sie, ob die Batterie
gemäß der angegebenen Polarität
(+ = oben) richtig eingelegt ist.
Setzen Sie die Rück- und Vorderseite
des Senders wieder zusammen. Der
Sender ist nun betriebsbereit.
Empfänger Batterieinstallation
Schieben Sie die Batteriefach-
abdeckung auf der Rückseite nach
unten und legen Sie die Batterien ein
(nicht im Lieferumfang enthalten)
4 x 1,5 Volt LR6 / Mignon. Beim
Einlegen bitte auf Polarität achten!
Schieben Sie die Batteriefach-
abdeckung des Empfängers wieder
ein. Der Empfänger ist nun
betriebsbereit.
Anschluss an eine vorhandene
Klingelanlage
Dieses Funkgong-Set ist auch
für den Anschluss an eine vorhandene
Klingelanlage geeignet.
Transmitter Battery Installation
The transmitter is operated by
a 3 Volt Lithium CR2032 battery,
which is included in delivery and is
pre-installed inside the transmitter.
Just remove the protective foil
sticking out from the side of
transmitter, which will establish the
electrical contact.
To change the batteries, first remove
the nameplate on the front of the
transmitter and unscrew the screw.
Then remove the back of the
transmitter by carefully pushing in the
latch with a small, thin screwdriver.
Replace the old battery. Please check
if the battery is inserted correctly
according to the polarity (+ = up).
Reassemble the back and front
of the transmitter. The transmitter
is now ready for operation.
Receiver Battery Installation
Push down the battery cover on
back and insert batteries (not
included in delivery) 4 x 1,5 Volt
LR6 / Mignon. Please mind the
polarity! Push the battery cover
of the receiver back into position.
The receiver is now ready for
operation.
Connection to an existing bell system
This wireless chime set is also
suitable for connection to an
existing door bell system. The
Instalacija baterije oddajnika
Oddajnik poganja 3 voltna litijeva
baterija CR2032, ki je vsebovana v
obsegu dobave in že vložena.
Odstranite samo zaščitno folijo, ki ob
strani gleda ven iz oddajnika, tako da
se vzpostavi električni kontakt.
Za menjavanje baterije najprej
odstranite ploščico za ime na sprednji
strani oddajnika in odvijte vijak. Nato
odstranite hrbtno stran oddajnika, tako
da zapah previdno potisnete noter s
pomočjo majhnega, ozkega izvijača.
Staro baterijo zamenjajte.
Prekontrolirajte, ali je baterija v skladu z
navedeno polarizacijo (+ = zgoraj)
pravilno vstavljena. Hrbtno in sprednjo
stran oddajnika zopet sestavite.
Oddajnik je sedaj j pripravljen za
uporabo.
Instalacija baterije sprejemnika
Pokrov predalčka za baterije na hrbtni
strani potisnite navzdol in vložite baterije
(niso vsebovane v obsegu dobave) 4 x
1,5 voltna LR6 / Mignon. Pri vlaganju
pazite na polarizacijo! Pokrov predalčka
za bateriji sprejemnika zopet potisnite
noter. Sprejemnik sedaj pripravljen za
uporabo.
Priključitev na razpoložljiv zvonec
Ta komplet z brezžičnim gongom je
primeren tudi za priključitev na
razpoložljiv zvonec.
Ugradnja baterija u odašiljač
Odašiljač pokreće 3-voltna litijeva
CR2032 baterija koja je obuhvaćena
isporukom i već je umetnuta. Samo
uklonite zaštitnu foliju koja bočno strši
iz odašiljača kako biste uspostavili
električni kontakt.
Za zamjenu baterije najprije uklonite
pločicu s imenom na prednjoj strani
odašiljača, a potom otpustite vijak.
Potom skinite stražnju stranu odašiljača
oprezno utiskujući zasun malenim,
uskim odvijačem.
Zamijenite staru bateriju. Provjerite je li
baterija pravilno umetnuta u skladu s
navedenim polaritetom (+ = gore).
Ponovno sastavite stražnju i prednju
stranu odašiljača. Odašiljač je sada
spreman za rad.
Ugradnja baterija u prijemnik
Potisnite pokrov pretinca za baterije na
stražnjoj strani nadolje i umetnite
baterije 4 x 1,5 V AA LR6/Mignon (nisu
obuhvaćene isporukom). Pri umetanju
pazite na polaritet! Ponovno utisnite
pokrov pretinca za baterije na
prijemniku. Prijemnik je sada spreman
za rad.
Priključivanje na postojeći sustav zvona
Ovaj komplet bežičnog signalnog
zvona također je prikladan za
priključivanje na postojeći sustav
zvona.
T
T
A + C
A + B
A + B
3
2
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Heidemann 70823 - HX Square at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Heidemann 70823 - HX Square in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Heidemann 70823 - HX Square

Heidemann 70823 - HX Square User Manual - German, Dutch, French, Italian - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info