534543

Harman Kardon HKTS 65BQ Manual

8
Zoom out
Zoom in
Previous page
1/12
Next page
HKTS 65BQ
8
Connections
Connections
Satellite and Center Speaker Connections
CAUTION: Before making speaker connections, be sure that your receiver or
amplier is turned OFF and its AC cord is unplugged from the AC power outlet.
Speakers and receivers/ampliers have corresponding (+) and (–) connection terminals.
Most electronics makers use red to denote the (+) terminal and black for the (–) terminal.
Newer Harman Kardon receivers conform to the CEA standard and use specic colors to
denote the (+) terminals of the speaker positions. See the table in Color-Coding System,
on page 4.
Each speaker wire included with your system has colored bands at both ends of the (+)
conductor that correspond with the colors dened by the CEA standard. This system
helps ensure that the speaker in each location is connected to the correct receiver or
amplier terminals. In addition to the colored bands at each end, each speaker wire’s (+)
terminal has ribs molded into its insulation to help you identify it.
FRONT
LEFT
FRONT
RIGHT
CENTER
SURROUND
LEFT
SURROUND
RIGHT
Front Left
Satellite Speaker
Surround Left
Satellite Speaker
Receiver/Amplifier
White Colored
Band
Blue Colored
Band
Green Colored
Band
Red Colored
Band
Gray Colored
Band
Center
Speaker
Front Right
Satellite Speaker
Surround Right
Satellite Speaker
It is very important to connect each speaker identically: (+) on the speaker to (+) on the
receiver or amplier, and (–) on the speaker to (–) on the receiver or amplier. Miswiring
one or more speakers results in thin sound, weak bass and a poor stereo image. With the
advent of multichannel surround-sound systems, connecting all of the speakers in your
system correctly is very important to achieving the proper ambience and directionality of
surround-sound program material.
Connecting Satellite Speakers without the Supplied Bases
+
–
A) Push Down on Cap
to Open Hole
B) Insert Bare Wire
into Open Hole
C) Release Cap
to Secure Wire
Insert the conductor with the colored band into the speaker’s red (+) terminal, and insert
the other conductor into the speaker’s black (–) terminal.
IMPORTANT: Make sure the (+) and (–) bare wires do not touch each other or the other
terminal. Touching wires can cause a short circuit that can damage your receiver or
amplier.
Connecting Satellite Speakers with the Supplied Bases
1. Remove the speaker’s base (see Shelf Placement, on page 5).
2. Pass the speaker wire through the opening in the speaker’s base.
3. Connect the speaker wires as described above.
4. Reattach the speaker’s base, as shown in the illustration.
Subwoofer: Wireless Connection
12
WIRELESS
CODE
DC 5V
INPUT
R
34
L
SUBWOOFER/
LFE OUT
Power
Supply
AC Cord
Power
Supply
Use either
connector
LFE Cable
(supplied)
1. Connect the supplied LFE cable from your receiver’s or processor’s subwoofer output
to either of the transmitter unit’s Input connectors.
• If your receiver/processor does not have a dedicated subwoofer output but does have
a set of preamp-level (volume-controlled) line outputs, use a stereo audio cable (not
supplied) to connect them to both of the transmitter unit’s Input connectors
2. Connect the transmitter power supply to the Power connector, and into a working AC
outlet,
3. Set the Wireless Code switches on the transmitter unit and subwoofer to the same
position.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Harman Kardon HKTS 65BQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Harman Kardon HKTS 65BQ in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info