542127
30
Zoom out
Zoom in
Previous page
1/32
Next page
29
Bei den mit * versehenen Teilenummern handelt es sich um
Verschleißteile, die einer natürlichen Abnutzung unterliegen und
ggf. nach intensivem oder längerem Gebrauch ausgetauscht
werden müssen. In diesem Falle wenden Sie sich bitte an
den Hammer Kundenservice. Hier können die Teile gegen
Berechnung angefordert werden.
The part numbers with an * are wear and tear parts, which are
subject to natural wear and which must be replaced after inten-
sive or long-term use. In this case, please contact Customer
Service. You can request the parts and be charged for them.
-55V Abdeckung beweglicher Arm, oben vorn Cover for movable arm, upper front side 1
-55H Abdeckung beweglicher Arm, oben hinten Cover for movable arm, upper rear side 1
-56 Datenkabel, oben Upper computercable 1
-57 Kreutzschlitzschraube Crosshead screw M8x10 4
-58 Lenkerabdeckung, hinten Handlebar cover, rear side 1
-59 Kreuzschlitzschraube Cross head screw ST 4.2x25 1
-60 Kunststoffkappe für Rotationsscheibe Endcap for rotation wheel 2
-61 Mutter Nut M10 2
-62 Rotationsscheibe Rotationwheel 1
-63 Metallkreuz für Rotationsscheibe Steel cross for rotation wheel 2
-64 Mutter Nut M12 1
-65 Netzgerätbuchse Plug for adapter 1
-66 Sicherungsring Spring ring Ø17 1
-67 Kugellager Ballbearing 6203RS 2
-68 Wird nicht benötigt No needed 0
-69 Sensor Sensor 1
-70 Kreuzschlitzschraube Crosshead screw M5x15 4
-71* Motor Motor 1
-72 Buchse Bushing Ø22xØ18x4 1
-73 Sechskantschraube Hex head screw M6x15 4
-74 Antriebsrad Drive wheel 1
-75 Achse Axle 1
-76 Mutter, selbstsichernd Safety nut M8 4
-77 Widerstandsverstellkabel Tension control cable 1
-78L Gehäuse, links Housing, left side 1
-78R Gehäuse, rechts Housing, right side 1
-79 Mutter Nut M10 2
-80a Augenschraube Eyelet bolt M6x25 2
-80b Anschlag Block 2
-80c Mutter Nut M6 2
-81 Schwungrad PMS Magnetic wheel PMS 1
-82 Riemenspanner Idler bracket 1
-83 Kugelllager Ball bearing 6201 2
-84 Kunststoffkappe, eckig für Pedalarm Endcap retangular for pedalarm 2
-85 Unterlegscheibe Washer Ø6 1
-86 Innensechskantschraube Allenscrew M6x10 1
-87 Augenschraube Eyelet screw M8x140 1
-88 Sechskantschraube Hex head screw M8x20 1
-89 Kreuzschlitzschraube Cross head screw ST 3.0x10 2
-90 Kreuzschlitzschraube Cross head screw ST 4.2x12 14
-91 Unterlegscheibe Washer Ø17xØ12x0.5 1
-92 Mutter Thin nut 2
-93 Griffmutter für Trittplatte Grip nut for pedal 4
-94 Mutter Nut Ø8 2
-95 Unterlegscheibe Flat washer 1
-96 Unterlegscheibe Flat washer Ø25xØ8.5x2.0 1
-97 Abdeckung Cover 1
-98 Unterlegscheibe Flat washer Ø12xØ4.5x1.0 2
30


Need help? Post your question in this forum.

Forumrules
1

Forum

hammer-cardio-ce1

Reset search

  • I have two crosstrainers Hammer Cardio CE1. The force I need to apply on the first is very different then on the other while all settings are exactly the same. How can this be? And how can I change this? I think the first one is correct and the other one needs far too little effort. Submitted on 13-8-2022 at 09:53

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hammer Cardio CE1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hammer Cardio CE1 in the language / languages: English, German as an attachment in your email.

The manual is 5,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info