607380
3
Zoom out
Zoom in
Previous page
1/16
Next page
4
5
Einrichten eines Warnsignals für die Innentemperatur
Halten Sie die ALERT-Taste 3-4 Sekunden gedrückt. Die
Innentemperatur und das Symbol für das obere Temperaturlimit
blinken.
Drücken Sie UP oder DOWN, um das obere Temperaturlimit für
das Warnsignal einzustellen.
Drücken Sie die ALERT-Taste. Daraufhin blinken die
Temperatur und das Symbol für das untere Temperaturlimit.
Drücken Sie UP oder DOWN, um das untere Temperaturlimit für
das Warnsignal einzustellen.
Drücken Sie die ALERT-Taste, um zum normalen Anzeigemodus
zurückzukehren.
Drücken Sie die ALERT-Taste, um die Warnfunktion zu aktivieren
oder zu deaktivieren. Wenn die Funktion aktiviert ist, werden die
Symbole für das obere und das untere Temperaturlimit angezeigt.
Einrichten eines Warnsignals für die Außentemperatur
Halten Sie die ALERT-Taste 3-4 Sekunden gedrückt.
Drücken Sie die CHANNEL-Taste, um den Sender auszuwählen,
für den das Warnsignal eingerichtet werden soll. (1 bis 3)
Daraufhin beginnen Außentemperatur und Symbol des oberen
Temperaturlimits für den betreffenden Sender zu blinken.
Drücken Sie UP oder DOWN, um das obere Temperaturlimit für
das Warnsignal einzustellen.
Drücken Sie die ALERT-Taste. Daraufhin blinken die Temperatur
und das Symbol für das untere Temperaturlimit.
Drücken Sie UP oder DOWN, um das untere Temperaturlimit für
das Warnsignal einzustellen.
Drücken Sie die ALERT-Taste, um zum normalen Anzeigemodus
zurückzukehren.
Drücken Sie die ALERT-Taste, um die Warnfunktion zu aktivieren
oder zu deaktivieren. Wenn die Funktion aktiviert ist, werden die
Symbole für das obere und das untere Temperaturlimit angezeigt.
Verwendung des Countdowntimers
Drücken Sie im normalen Zeitanzeigemodus dreimal die MODE-
Taste, um den Countdowntimer anzuzeigen. Daraufhin wird auf
der LCD der Eintrag TIMER angezeigt.
Halten Sie die SET-Taste 3-4 Sekunden gedrückt, bis die
Stundenzahl zu blinken beginnt.
Drücken Sie UP oder DOWN, um die Stunde einzustellen.
Drücken Sie SET. Daraufhin beginnt die Minutenzahl zu blinken.
Drücken Sie UP oder DOWN, um die Minuten einzustellen.
Drücken Sie SET. Daraufhin beginnt die Sekundenzahl zu blinken.
Drücken Sie UP oder DOWN, um die Sekunden einzustellen.
Drücken Sie die SET-Taste, um die eingestellte Zeit zu
übernehmen.
Drücken Sie SET, um den Countdowntimer zu starten.
Während das Zählwerk abwärts zählt, können Sie jederzeit die
SET-Taste drücken, um den Vorgang anzuhalten. Zum Fortfahren
drücken Sie die SET-Taste noch einmal.
Wenn das Zählwerk bis -00- zurückgezählt hat und das Signal
ertönt, können Sie den Signalton mit einer beliebigen Taste an der
Vorderseite des Geräts ausstellen. Auf der LCD wird wieder die
normale Zeitanzeige angezeigt.
Wenn Sie den Wert für das Zählwerk löschen oder neu einstellen
möchten, bevor -00- erreicht wird, halten Sie den Countdowntimer
an und geben einen neuen Zeitwert ein. Verfahren Sie dabei nach
der angegebenen Schrittfolge.
Reset
Das Thermometer, mit dem Sie die Temperatur in mehreren
Bereichen gleichzeitig messen können, kann bei Betriebsstörungen
jederzeit zurückgesetzt werden. Drücken Sie einmal die RESET-
Taste. Daraufhin werden alle Werte auf die Werkseinstellungen
zurückgesetzt. Legen Sie die Einstellungen nun wie in der
Bedienungsanleitung beschrieben neu fest.
Zulassungs- und Sicherheitsbescheinigungen/Allgemeine
Informationen
Dieses Gerät trägt die CE-Kennzeichnung entsprechend den
Bestimmungen der Directive R&TTE (1999/5/EG).
Hama GmbH & Co. KG erklärt hiermit, dass sich dieses Gerät
in Übereinstimmung mit den grundlegenden Anforderungen
und den weiteren relevanten Regelungen und Vorschriften der
Richtlinie 1999/5/EG befindet. Die Konformitätserklärung und die
Übereinstimmungserklärung nden Sie im Internet unter http://www.
hama.com.
Features and Specifications
Base Station
Indoor/outdoor RF temperature
Monitors temperature at up to 4 locations
(additional sensors required)
Indoor/outdoor temperature displayed in °C or °F
Memory funcion to recall highest/lowest temperature readings
Indoor temperature range: -10°C to 70°C (14°F to 158°F)
Temperature tolerance: +/– 1,1°C (+/– 2°F)
12/24 hour selectable alarm clock with snooze
Month/day/year calender
Countdown timer
Low battery indicator
Table top or wall mount
Requires 2 AAA batteries
Remote Sensor
433 MHz transmission frequency
Transmission range up to 30 m (range may be shorter based on
interference present)
Temperature range: -20°C to 70°C (-4°F to 158°F)
Temperature range via sensor probe: -40°C to 70°C (-40°F to 158°F)
Temperature tolerance: +/- 1.1°C (+/- 2°F)
Table top or wall mount
Requires 2 AAA batteries
Battery installation and setup
Position the remote sensor near the base station.
Open the battery compartment at the back of the base station and
insert 2 AAA batteries according to the polarity markings.
Replace the battery compartment cover.
Press the UP C/F button at the back of the unit to display the
temperature in °C or °F.
The RF signal icon (located to the left of the outdoor temperature
display) will ash for 5 minutes, inicating that the base station is
ready to pick up the RF signal from the remote sensor.
Register the remote sensor
Open the battery compartment at the back of the remote sensor
and slide the channel selector switch to your desired channel. For
the rst remote you may select any channel, for additional
remotes select any unused channel.
Insert (2) AAA batteries according to the polarity markings. Be
sure to install the batteries in the remote within the time that the
RF signal icon is ashing on the base station.
Replace the battery compartment cover.
If you have registered more than one sensor, press the CHANNEL
button to select the remote channel you want displayed
permanently on the base station. Or press CHANNEL until you
observe a circular arrow on the base station LCD display under
the channel number. The unit will then auto-scroll, changing from
channel to channel every 5 second.
Register a remote sensor when the RF signal icon is not showing
To register a remote sensor when the RF signal icon is not showing on
the base station LCD:
Press and hold the CHANNEL button for 3-4 seconds until the RF
signal icon is showing.
Install the batteries in the new remote sensor or if the batteries
have already been installed, press either the TX or RESET button,
which are located inside the remote battery compartment.
Note:
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable
(nickel cadmium) batteries.
For maximum performance in nomal conditions we recommend
using good quality alkaline batteries. When temperatures are
below 0°C, alkaline batteries can lose power resulting in a loss of
remote transmission. If you reside in an area that experiences
frequent temperatures near or below 0°F, we recommend using
lithium batteries to minimize the loss off transmission.
Locating the base station and remote sensor
Chosse a suitable place for the base station and remote outdoor
sensor, within the transmission distance.
Place the base unit near a window, but away from direct sunlight
or sources of heat or air conditioning to ensure accurate
temperature readings.
The remote sensor is water resistant, but not waterproof. Locate
the sensor out of direct sunlight, in an area where it will not be
exposed to rain, snow or ice.
The location you chosse is critical for maximizing the transmission
range. The remote sensor is desighned to transmit up to 100 ft.
unimpeded. Transmitting through walls, metal doors and metal
framed windows may reduce the transmission range. To optimize
the transmission distance, the remote should be positioned in a
location that minimizes these obstructions. Interference from
other sources such as home security systems, wireless doorbells
and wireless home entertainment equipment may interrupt the
transmission signal temporarily.
g
Operating Instruction
MODE CHANNEL MAX/MIN
UP °C/°F
SET/AL
ON/OFF
DOWN
12/24
ALERT
RESET
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hama EWS100 - 99076043 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hama EWS100 - 99076043 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info