122823

Hama 40085 2 in 1 Manual

3
Zoom out
Zoom in
Previous page
1/15
Next page
4
5
g
Operating Instruction
g
Operating Instruction
g Operating Instructions
Universal Remote Control
Function Keys
1. Turns the device on or off.
2. Mute the sound.
3. CH± : Works like the Channel Up and Down
key on your original remote control.
4. VOL±: Control the volume like the Volume Up
and Down key on your original remote control.
5. SET: Setup/Confi guration of the remote
control.
6. TV, SAT(/CBL): Let you select the
device you want to control.
General Description:
Thank you for purchasing the Hama 2 in 1
universal remote control. This remote control
contains one of the most extensive code
libraries. This remote control allows you to
operate a maximum of 2 devices. It is suitable
for a large quantity of TVs and satellite recei-
vers (CBL/SAT) found on the market today.
A control LED supports the programming of
the remote control. The Hama 2 in 1 universal
remote control controls all essential basic
functions of your devices. Please read this
instruction manual carefully in its entirety
before using this remote control for the fi rst
time.
Inserting batteries:
This remote control requires 2 AAA batteries
(not included) for operation.
1. Turn the remote control over and open the
back cover.
2. Insert the batteries. Make sure the
polarity is correct. (See the (+) and (-)
markings in the battery compartment)
3. Insert the cover back into its original
position.
The 2 in 1 is a new model of preprogrammed
universal remote control for European market
which has an extensive code library, power-
ful function and stable quality .It features as:
A. Totally 2 device keys: TV, SAT
[Analogue Satellite, digital Satellite,
Cable]
B. Operation Modes: Set-up Mode, Manual
Search Mode and Auto Search
C. Back-up memory to keep the set up data
no- volatilization.
D. LED fl ash to indicate when transmission.
E. Set-up indicating LED
F. Punch-through function
Code Set Up
A. Set Up by Manual Search:
a. Power on the device that you want to
control. If it is a VCR, it must be inserted
with a tape.
b. Press and hold the [SET] keys. Then press
the device key in remote control, such as
[TV], [SAT]
c. The LED will be on at moment. Then
release the pressed keys.
d. Point the remote control to the device,
strike the [POWER] key. The remote control
enters into ”Manual Search” mode and the
LED keeps fl ashing.
e. See if device reacts or not. If it works, turn
to step f; If not, repeat step d every 1
second.
f. Test other keys. If keys work well enough,
press the device key to quit from the
search mode. If most keys don‘t work well
enough, repeat step d-f to fi nd the best
code.
Remarks:
a. Whenever you want to leave or change
search mode, press the device key to quit,
and the LED will turn off.
b. In the Manual Search Mode, besides the
[POWER] key, all other keys‘ function can
be checked normally. That is to say you
can test other keys without leaving Manual
Search mode. It will leave Manual Search
mode automatically if no key pressed in 30
seconds.
c. You may use the SET key to change the
search direction from forward to backward
or from backward to forward.
B. Set up by Auto Search:
This search is similar to Manuel Search
except it transmits power signal automatical-
ly instead of manually pressing the power key
during the search:
a. Power on the device you want to control.
b. Press and hold [SET] key, in the meantime,
press and hold the Device key that you
want to control. (for example: TV) for more
than 3 seconds and then release them, the
auto search begins. The remote control
enters into Auto Search, LED fl ash, and
remote control transmit power signal every
2.0 second automatically.
c. See if device react or not, once the device
reacts, press any key (except SET key) to
stop the search.
d. Test if other keys work well enough. If
most keys work not good enough, Auto
Search again to fi nd next reactive code
and try until you fi nd the best code.
Remark:
a. You must point your remote control to the
device that you want to control during
Auto Search.
b. Whenever you want to leave Auto Search
mode, press any key (except SET key) to
quit, and the LED will be Off. The search is
over.
c. When remote control search through all
codes (about 10 minutes), then the remote
control will quit from Auto Search process
automatically.
d. In case of you did not stop the search on
time when device reacted, you may use
the Manual Search to search back to fi nd
the passed code.
Other Features
Punch-through Function
When you change the device from one to
another, if another device doesn‘t have
volume key and mute key, the remote control
will remain the volume key and mute key of
last device.
Others
a. After you have fi nished set-up, fi rst please
press the device key (TV or SAT) on
remote control that you want to use, and
then operate your remote control normally.
b. An LED indicates which device is being
used. Sometimes a different device is
displayed from the one in operation (or
the last pressed device selection key). In
this case the “punch through” function is
active.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hama 40085 2 in 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hama 40085 2 in 1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info