607802
5
Zoom out
Zoom in
Previous page
1/10
Next page
5
Deutsch
Programming your universal remote control with
automatic code scan
Important:
We recommend manually entering and trying all codes given for your
device before running an automatic code scan.
If the listed codes are not working for your TV set, etc., or if the manufacturer
of your device is not listed, you have the option to let the remote control find a
suitable code by means of the automatic code scan. During this procedure,
every code is tested on your devise and a signal is sent approximately every 2
seconds. As soon as a suitable code has been found, the device will respond
according to the key that has been pressed. You must now test the other
functions of your remote control. If some of them appear not to be available,
this might be due to the fact that only the first of many matching codes has
been detected so far. In this case, continue with the code scan until a more
suitable code is found. Please be patient, as a great number of different codes
must be tried out during the scanning process. It might therefore take up to 8
minutes until the correct code for your device is found.
How to run an automatic code scan (code 0020)
Step 1 Switch on the respective device. For television sets, ensure that a
picture is displayed. If your TV set is in standby mode, switch it on
fully. For instructions, please refer to the TV set manual.
Step 2 Select the device that you wish to control with your universal remote
control by turning the rotary indicator until the arrow points to the
desired device. (only for M5)
Step 3 Press the key until the LED flashes twice. (after approx. 2 seconds).
Step 4 Enter code 0020 (within 5 seconds). The LED again flashes twice to
indicate that the remote has entered its programming mode.
Step 5 Code scan for TV set or SAT receiver (only for M5)
After the LED has flashed twice, press the key and keep it pressed
until the device has switched off. During the code scan, the LED
flashes every 2 seconds, this indicates that the automatic is in
process. After the device has switched off, switch it on again (using
the remote) to check the other functions of the remote control.
Code scan for VCR (only for M5) or DVD (only for M5)
Insert a videotape or DVD and play it (by pressing the key on your
video recorder/DVD player).
During the code scan for your VCR/DVD player, press and hold down
the key until the videotape/DVD has stopped. Then you can test the
other functions of your remote control.
PLEASE REMEMBER THAT THE FIRST FOUND CODE MIGHT NOT
BE THE MOST SUITABLE FOR YOUR DEVICE.
Step 6 If all functions work as desired, press the key to save the found code.
IMPORTANT!
After the device has been switched off (step 5), you have the option to test the
control functions. If a selected code does not support all required functions,
press the key to go to the next code. After all saved codes have been
scanned, the LED flashes three times.
How can I run a code scan for one manufacturer only
(code 0021)?
To run a code scan that is limited to the codes of one specific manufacturer,
proceed as described for "automatic code scan" (see above chapter).
However, in this case enter code 0021 followed by the code of your device
manufacturer. This code is listed in the appendix of this manual.
IMPORTANT!
As soon as the red LED flashes three times, the scan through the codes of your
manufacturer is completed. If your device has not yet responded, run an
automatic code scan.
USER MANUAL
GB
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hama 20305 - Easytip M1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hama 20305 - Easytip M1 in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hama 20305 - Easytip M1

Hama 20305 - Easytip M1 User Manual - German - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info