659860
6
Zoom out
Zoom in
Previous page
1/8
Next page
6
Before using the unit
Please read through the instructions
carefully before using the unit and note
carefully the safety advises. Store the
manual safe and handy.
Scope of application
The equipment can be set up in a cabi-
net or can be used as a portable unit in
a carry case. It is suitable for the follow-
ing scopes:
Footcare: Milling, trimming and polish-
ing. Attention: In fields of footcare
ones have to work with spray.
Dental technique/ -laboratory:
Milling-, trimming and polishing work
at plaster casts and models (Do not
use this unit directly at the patient.)
Manicures: smoothing, trimming and
polishing.
Location of installing
The installation of the workroom must
correspond to the governing regula-
tions. Set up the appliance so that the
ventilation slits are not covered and the
exhaust air can escape well. Now con-
nect the power-supply plug to the elec-
tricity.
Fill in the spray liquid
Reduce the speed of the handpiece
with regulator (3) on minimum. Pull out
the spray tank at the grip. Hold on to the
tank cover with one hand and turn the
container of the tank off.
Now fill it with distilled water and anti
germ liquid (e.g. AQUA HY item no.
8555).
Do not exceed the maximum level
when filling the tank.
While screwing back the cover on the
tank, make sure that is closed correct.
Otherwise there will no pressure be
build up.
Put the tank back in the housing.
Turn on the unit on the main switch
(located on the back of the unit)
.
Attention: Never us tap water. (Dan-
ger of calcification). Also do not use
explosive or combustible liquids e.g.
alcohol.
Note: The filter in the tank (item no.
3479) should be fully under pressure,
otherwise no water will be sucked in.
11
Maintenance and care
Cleaning the chuck
Because of the washer, very little
dirt might enter the handpiece. In
the curse of the time, dirt can ap-
pear and might interrupt the perfor-
mance of the handpiece. Therefore
clean the chuck monthly.
Dismount the chuck
Unscrew the top of the handpiece
while using the tongs key:
Clean the inside and the top of the
handpiece now with a dry brush.
Push the black knob forward to
open the chuck.
Set the first key (see picture below) on
the axle and hold it tight. Screw out the
chuck with the second key, which has
the forefront
.
The assembly of the clamping device
takes place in reverse order. Make sure
that the clamping device is opened
when assembling it.
Cleaning the chuck
Soak the chuck in white spirit or in a
special fluid for cleaning tools. Clean
the slots of the chuck and the drilling
with a brush or a scrubber.
Rinse off the chuck well and let it dry.
Place a small drop of oil on your thumb
and pointer. Rub both fingers until you
find very little of oil on your fingers.
Now take the chuck and put it between
these two fingers and turn it around.
There should only be a very slight film
of oil on the chuck. It counts: Less is
more than too much
.
6


Need help? Post your question in this forum.

Forumrules
1

Forum

hadewe-spr3

Reset search

  • Dear Sirs,

    I wonder about the the speed that should be used for good results on skin and on nails. Could you help me please with recomendation?

    Thank you in advance! Submitted on 4-8-2023 at 22:53

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hadewe SPR3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hadewe SPR3 in the language / languages: English as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hadewe SPR3

Hadewe SPR3 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info