659873
4
Zoom out
Zoom in
Previous page
1/28
Next page
4
Safety Instructions
The equipment should only be
used by trained operators.
The installation of the working
area has to correspond to the
relevant regulations. Set up
the unit in such a way, that the air slits
are not blocked and the extracted air
can escape well.
To avoid the risk of electrocu-
tion only connect the device to
the mains power supply.
If you pull the power plug it will
stop the connection to the
mains power supply. Set up
the unit so that the power plug is always
accessible. The power switch should
also always be easily accessible.
Only switch on the unit, if the
handpiece rests secured in the
handpiece holder, or if you
hold it safely in your hand.
Prevent any liquids from
entering into the control unit,
since this could damage the
electronic elements.
Clean the outside of the box only with a
damped cloth. Make sure, that you have
unplugged the unit before.
Only when pulling the mains
cable, you can ensure that the
device will be completely
disconnected from mains.
Check the mains cable regularly for
damages and in case of such, have it
be changed or repaired by an author-
ized service center.
Prevent your hair from
wrapping itself around moving
parts. If applicable, wear a
hair net.
When working with materials,
which might create dust or
moisture, use a drilling unit
with suction or spray tech-nique. Wear
a nose and mouth protec-tion. Always
follow the safety instruc-tions, provided
by the manufacturer of the materials
being formed and used.
For safety reasons you must
always wear disposable
gloves and protective glasses
when operating this unit. In addition, a
face mask conforming to EN 14683 type
IIR or EN 149 FFP 2 must also be worn.
Ensure that the patient’s foot
and the handpiece are held
firmly in place during the
operation. To prevend injury, work with
extreme caution on the foot of the
patient, and use only light pressure
To ensure that the bur/ tool
sits firmly in the chuck, do not
work with tools which:
have an oily shaft
are worn
are bent
Before using the equipment, assure
that:
the tool can be pushed far enough
into the chuck
(Test this with a dipstick and clean
if necessary)
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hadewe SB2 -Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hadewe SB2 -Series in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info