633020
3
Zoom out
Zoom in
Previous page
1/16
Next page
3
2.0 - INSTALLATION AND CONNECTIONS
WARNINGS:
- Complete a pre-installation check and disconnect the negative terminal of the vehicle’s
battery. .
- Before fixing the device, insert the installation loom connectors into the alarm and
screw the connector cover on.
- Place the alarm system in the engine compartment, away from direct sources of
water spray and high tension wiring.
- Solder and isolate all connections.
- Connect the BROWN wire to the negative terminal of the vehicle’s battery (power supply
negative).
- Connect the RED (general power supply) and RED/WHITE wires (indicator relay positive)
to the positive terminal of the vehicle’s battery with a 15A fuse.
- Connect the YELLOW wire to an ignition switched live (+15/54) that remains live even
when the engine is being cranked.
- ORANGE wire (INDICATOR Command): if the INDICATOR COMMAND is DISABLED
connect to the vehicle right indicators (or to the left). If the INDICATOR COMMAND function
is ENABLED with this wire is possible to command the indicators (only on the vehicles
equipped with this function - See the INDICATOR COMMAND diagram). For the connection
refer to the technical installation guides.
- Connect the ORANGE/BLACK /wire (FEEDBACK) to the vehicle left (or right) indicator by
a diode(2 Amp) (see the INDICATOR COMMAND diagram).
- Connect the GREEN wire to the switches for the boot and bonnet protection.
- Connect the GREEN/BROWN wire to the original door pin switches. This alarm input is
set by default to manage the negative stable signals. It is possible to manage also the
vehicles original switches with negative impulsive signals(pulsing) enabling the Function
No.6 PULSING management. For the connection refer to the technical installation guides.
It is possible to manage also the positive stable signals enabling the Function No.7
Postive Door pin switch management.
- Connect the PINK wire (Positive output when the alarm is armed - Max capacity 80 mA to
the PINK wire of modules or additional sensors (i.e. ultrasonic module).
- Connect the GREEN/BLACK wire (alarm input by optional additional sensors) to the
GREEN/BLACK wire of the same (i.e. ultrasonic module).
- Connect the BROWN wire (Sec. 0,35mm²) to the modules or additional sensors (i.e.
ultrasonic module).
- The RED/BROWN, RED/GREY, RED/BLUE, YELLOW/BROWN, YELLOW/GREY and YELLOW/
BLUE wires are used to command the central door locking referring to the instuctions in
the technical installation guide.
WARNING:
- Always use 5 A fuses on the RED/BLUE and YELLOW/BLUE wires.
- The max. load to command the central door locking is 5 A. For example it is not
possible to drive directly No.4 GT71 actuators (see diagramNo. 5).
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 915 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 915 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info