554283
4
Zoom out
Zoom in
Previous page
1/4
Next page
4
GT613UKRev02.p65
USER MANUAL - HOW TO USE THE ALARM
ARM/DISARM THE ALARM
By the original handset. Closing the doors the alarm sets after about 3and opening the doors it unsets within
about 3. For correct system operation, it is necessary to wait for at least 5seconds between an arming
operation and a disarming operation.
WARNING: The emergency indicators (HAZARD) activation doesnt
allow the alarm arming and disarming.
ELECTRIC WINDOWS CLOSURE COMMAND FUNCTION (IF CONNECTED)
The electric windows closure is controlled when arming.
PROTECTIONS
(1) Passive engine immobilisation
(2) Doors, boot and bonnet contacts. (When arming, you may observe a long flash of the indicators, it means
that a door hasnt been correctly closed ).
(3) Power supply wires disconnection (for self-powered alarms and on armed alarms only). The interruption
of the positive feed (RED wire) doesnt stop the vehicle (FAIL SAFE facility).
(4) Shock sensor protection.
(5) Additional sensors.
IF THE ALARM SOUNDS
Should the siren activate, it will sound for about 28. A press of the original
handset button will silence the siren
and disarm the alarm.
CHECK LED
Your alarm system is equipped with check control flashing LED in order to
verify an alarm state. If the alarm has been triggered when the vehicle
was unattended the LED will then start to flash irregularly according to the
triggered sensor (see table). Record the number of flashes and inform your
installer. NOTE: Two or more triggers on different sensors (i.e. doors and
bonnet) will be signalled in order by the LED (i.e. 4 - pause - 5 flashes -pause
- 4 - etc.).
DISARMING EMERGENCY
When it is not possible to disarm the alarm by the handset you may disarm the
alarm following the instructions on the GT CARD CODE.
TO ISOLATE THE ADDITIONAL SENSOR WHEN ARMING
When the alarm is disarmed open a door and switch the the ignition on and off twice. The LED starts to flash. Arm
the alarm; from this moment the additional shock sensor/s will be isolated.
To delete the additional sensor isolation operation it is necessary to disarm the alarm, or if it is already disarmed,
turn the ignition key once.
ARMING/DISARMING ACOUSTIC SIGNAL FACILITY
With this facility it is possible to have the acoustic signal beepwhen the alarm is arming or disarming.
FACILITY CHECK
It is suggested to check periodically the facility to obtain a system in working order.
WARNING:
To insert or to isolate the underlined facilities, contact your Installer.
LED
(flashes)
ENTRY SENSOR
2 additional
3 shock sensor
4 doors
5 boot/bonnet
6 ignition key
7 wires cut
WARRANTY CONDITIONS
This Certificate should be kept in a safe place and produced for verification should technical assistance be
required. Inability to produce this Certificate may affect your warranty rights. Warranty period bengins from date
of purchase and is valid for 12 months (24 months U.K.).
Should technical assistance be required during the warranty period, you should take your vehicle and this
Certificate to either the original installer or the nearest GT Auto Alarm Service Centre for inspection. Should any
part of the security system be found to be defective, and providing all component parts of the system are of GT
Auto Alarm manufacture, the defective part will be replaced or repaired free of charge. Warranty replacement/
repair does not include the following items:
1) damage caused in transit/carriage;
2)damage caused by incorrect or poor installation; problems which may be caused by anomalies in the vehicles
electrical system or originating from the environment in which the system is operated.
3) damage caused by carelessness, negligence, misuse or repair by unauthorised personnel.
Units returned to our organisation under the terms of the warranty will be replaced or repaired within a reasonable
time period according to our Company requirements.
Any repair/refurbishment received within the warranty period does not extend or renew the warranty itself.
Nobody is authorized to modify or replace anything in verbal or written format which alters the conditions of this
warranty.
The manufacturer reserves the right to modify or improve the specification.
The alarm only deters attempted theft. Our company cannot accept liability for any consequential damage or loss to
persons or property as a result of purchase of a GT Auto Alarm system.
Any correspondence for litigation purposes shall be received at our headquarters in Gavirate (Varese) - Italy.
?
Installation Certificate
We certify that the alarm system installation has been carried out following the
installation instructions and the information in the owner's guidehas been passed over
to the customer.
Warranty coupon
Alarm model:
ALARM MODEL: INSTALLATION DATE: INSTALLED ACCESSORIES:
POSSIBLE INSTALLED ACCESSORIES: STAMP AND INSTALLER SIGNATURE: INSTALLATION DATE:
MARK AND CAR MODEL: STAMP AND INSTALLER
SIGNATURE:
All GT Auto Alarm lines are homologated according to the European Directives.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GT 615 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GT 615 in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info