110462
7
Zoom out
Zoom in
Previous page
1/10
Next page
ENGLISH
14
Setting up the device
The speaker for the device is located at the bottom of
the device.
To optimise the sound, mount the device holder on the
bottom of the device.
UP MODE
DOWN TIMER
VOL.
MEMO
SET
ON OFF
1 2
543
6 7
8 9 10
1 Click the device
holder in place in
the recesses on the
bottom of the
device.
Mounting the device under the counter
The fixing screws can be found in the side compart-
ment of the packing.
ONOFF
1 2
543
6 7
8 9 10
UP MODE
DOWN TIMER
VOL.
1 Mark the locations
for four mounting
screws.
2 Screw the device
holder on with four
screws.
UP MODE
DOWN TIMER
VOL.
MEMO
SET
ONOFF
1 2
543
6 7
8 9 10
3 Insert the device in
the holder.
Note:
7
To remove the device, press the snap-catch at
the back and remove by pulling forward.
Setting radio stations
There are 10 channel positions available for radio sta-
tions.
1 Switch on the device with »ON/OFF«.
2 Begin station search by pressing and holding down
»UP« or »DOWN«.
The search stops, as soon as a radio station with a
sufficiently strong signal is found.
If RDS information is transmitted by the station cur-
rently set, »f« appears in the display and after a
short time the station name appears in place of
the frequency.
INSTALLATION AND SETTINGS ________________
Note:
7
You can also set the frequency step-by-step
(50 kHz) by briefly pressing »UP« or »DOWN«.
Only 100 kHz steps are shown in the display.
3 Save radio station by pressing »MEMORY«
P -« flashes in the display ), select the desired chan-
nel position within 8 seconds with »1 10« and
confirm with »MEMO SET«.
»1 … 10« press once for channel positions
1 … 5, twice for channel positions 6 … 10.
Display: the channel position is shown briefly, and
then the frequency.
4 To set further radio stations, repeat this procedure
starting at pt. 2.
Note:
7
If no channel position is selected within 8 sec-
onds, the device interrupts the setting procedure.
Start again at pt. 3.
Setting the time automatically
1 Select a channel position with an RDS station to au-
tomatically set the time.
The display »¥« flashes, the current time is set by
the RDS time signal. This process may last a few min-
utes.
If an RDS time signal was received, the indicator
»¥« is illuminated.
Note:
7
If the time is not automatically set, select another
channel position with an RDS station by pressing
»1 10«, »¥« flashes in the display.
7
If your device cannot automatically set the time,
you can enter the time manually.
Setting the time manually
1 Switch off device with »ON/OFF«.
In the display, »12:00« flashes.
2 Press »MEMO SET« and hold down.
3 Set the time with »UP« or »DOWN«.
When »UP« or »DOWN« are held down, the
time can be set more quickly.
4 Release »MEMO SET«.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grundig Sonoclock 890 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grundig Sonoclock 890 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Grundig Sonoclock 890

Grundig Sonoclock 890 User Manual - German - 11 pages

Grundig Sonoclock 890 User Manual - Dutch - 13 pages

Grundig Sonoclock 890 User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info