759533
4
Zoom out
Zoom in
Previous page
1/6
Next page
1
D
Anwendungsbereich
Der Betrieb mit drucklosen Speichern (offenen
Warmwasserbereitern) ist nicht möglich!
Technische Daten
Fließdruck min. 0,5 bar /empfohlen 1-5 bar
Betriebsdruck max. 10 bar
Prüfdruck 16 bar
Zur Einhaltung der Geräuschwerte nach DIN 4109 ist bei
Ruhedrücken über 5 bar ein Druckminderer einzubauen.
Höhere Druckdifferenzen zwischen Kalt- und
Warmwasseranschluss sind zu vermeiden!
Durchfluss bei 3 bar Fließdruck ca. 13 l/min
Temperatur
Warmwassereingang max. 80 °C
Empfohlen: (Energieeinsparung) 60 °C
Installation
Rohrleitungssystem vor und nach der Installation
gründlich spülen (DIN 1988/DIN EN 806 beachten)!
Einbau und Anschluss, siehe Klappseite II, Abb. [1] bis [5].
Maßzeichnung auf Klappseite I beachten.
Ablaufgarnitur einbauen, siehe Klappseite II, Abb. [3].
Kelch abdichten!
Anschluss
Verbindung der Seitenventile mit den Versorgungsleitungen
herstellen.
Kalt- und Warmwasserzufuhr öffnen und Anschlüsse auf
Dichtheit prüfen.
Wartung
Alle Teile prüfen, reinigen, evtl. austauschen und mit Spezial-
armaturenfett einfetten.
Kalt- und Warmwasserzufuhr absperren.
Oberteil, siehe Abb. [6].
Seitenventil gegen Zurückrutschen sichern!
Mousseur, siehe Klappseite I.
Ersatzteile, siehe Klappseite I (* = Sonderzubehör).
Pflege
Die Hinweise zur Pflege dieser Armatur sind der beiliegenden
Pflegeanleitung zu entnehmen.
GB
Application
Operation with low-pressure displacement water heaters is
not possible!
Technical data
Flow pressure min. 0.5 bar / recommended 1 - 5 bar
Operating pressure max. 10 bar
Test pressure 16 bar
If static pressure is greater than 5 bar, fit pressure reducer.
Avoid major pressure differences between cold and hot water
supply.
Flow rate at 3 bar flow pressure: approx. 13 l/min
Temperature
Hot water inlet: max. 80 °C
Recommended: (energy saving) 60 °C
Installation
Flush piping system prior and after installation of fitting
thoroughly (Consider EN 806)!
Installation and connection, see fold-out page II, Figs. [1]
to [5].
Refer to the dimensional drawing on fold-out page I.
Fit pop-up waste set, see fold-out page II, Fig. [3].
Seal plug-hole rim!
Connection
For this purpose the side valves must be connected to the
supply lines.
Open cold and hot water supply and check connections
for watertightness.
Maintenance
Inspect and clean all parts, replace as necessary and grease
with special grease.
Shut off cold and hot water supply.
Headpart, see Fig. [6].
Secure side valve against sliding back!
Mousseur, see fold-out page I.
Replacement parts, see fold-out page I (* = special
accessories).
Care
For directions on the care of this fitting, refer to the
accompanying Care Instructions.
CH
应用
允许与低压排量热水器一起使用!
技术数据
水流压力 最小为 0.5 巴 / 建议值为 1 - 5
工作压力 最大为 10
测试压力 16
如果静压超过 5 巴,请加装减压装置。
避免冷热水间产生大的压差。
水流压力为 3 巴时的流量: 约为 13 升/分
温度
热水入水口: 最高 80 °C
建议值: (节能)60 °C
安装
安装前后务必彻底冲洗所有管件 (考 EN 806)
安装和连接,参见折页 II 中的图 [1] [5]。
参考折页 I 上的尺寸图。
安装溢水组件装置,参见折 II 图 [3]。
密封管口套圈!
连接
为了达到这一目的,必须将侧阀连接到供水管。
打开冷热水供应管,检查连接的防水性。
维护
检查和清洁所有零件,根据需要更换零件并用专用润滑油脂润
滑零件。
停止冷热水供应。
龙头部分,参见图 [6]。
将侧阀门紧贴滑动后盖固定!
出水嘴,参见折页 I。
备件,参见折页 I (* = 特殊零件)
保养
有关保养该产品的指导说明,请参考附带的 “保养指南”
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grohe 20377 - BauMetric at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grohe 20377 - BauMetric in the language / languages: English, German as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info