708325
3
Zoom out
Zoom in
Previous page
1/305
Next page
English (original instructions)
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
2
11. Wrench
12. Top handle
13. Sprocket cover tighten nuts
14. Sprocket cover
15. Chain tensioner adjustment screw
16. Bolt for saw chain tension
17. Sprocket
18. Battery release button
19. Oil outlet
20. Bar groove
21. Chain drive links
22. Cutter
23. Felling direction
24. Danger zone
25. Escape route
26. Direction of fall
27. Notch
28. Felling back cut
29. Hinge
30. Limb cut
31. Keep work off ground leave support
limbs until log is cut
32. Log supported along the entire length
33. Cut from top (over buck) avoid cutting
earth
34. Log supported one end
35. Under buck
36. Over buck
37. Log supported both ends
38. Bucking a log
39. Stand on uphill side when cutting be-
cause log may roll
ASSEMBLY
This top handle saw requires no assembly,
but user should know how to assemble the
guide bar and saw chain. Check the chain
tensioning and add oil as described later in
this manual before each operation.
ASSEMBLING THE GUIDE BAR AND
SAW CHAIN See figure 2 - 7
Make sure remove the battery pack from
the unit. Wear protective gloves.
Unscrew the sprocket cover tighten
nuts and remove the sprocket cover.
The saw chain should face in the
direction of chain rotation. If they face
backwards, turn the loop over.
Place the chain drive links into the bar
groove.
Position the chain so there is a loop at
the back of the bar.
Hold the chain in position on the bar
and place the loop around the sprocket
and make sure it is correctly mounted.
Make sure the bar hole ts well with
bolt for saw chain tension.
Replace the sprocket cover, turn the
chain tension adjust bolt clockwise until
the saw chain is properly tensioned.
The guide bar must then be pushed
upwards, check chain tension again,
do not tension the chain too tight.
After the chain is well-tensioned,
tighten the nuts again.
NOTE: The saw chain is properly ten-
sioned if, in the middle of the guide bar, it
can be lifted 3mm to 4mm from the edge
of the guide bar. Start the saw again with
a new saw chain, allowing it to run-in for
2~3 minutes.
WARNING
After the run-in time, check the chain ten-
sion and retighten the chain if necessary.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks GD40TCS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks GD40TCS in the language / languages: All languages as an attachment in your email.

The manual is 10,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info