725139

Gloria Multibrush li-on Manual

30
Zoom out
Zoom in
Previous page
1/99
Next page
31
Battery power (green LEDs):
Reserve ≤ 30% ≤ 60% 100%
Temperature protection / low voltage
cutoff:
7.1.2 Battery operating time
The service life of the battery mainly
depends on the load applied to the devi-
ce. Any cleaning work performed by app-
lying the brush with high pressure on the
surface to be cleaned will shorten the ser-
vice life of the battery.
Another factor is overly frequent starting
and stopping during cleaning, which can
also reduce battery operating time.
Handle battery and device as described in
the instructions.
7.1.3 Assembly of the brushing
tools
Figures 12 - 20
CAUTION
RISK OF BURNS CAUSED BY HOT
PARTS!
During assembly or conversion work
the drive parts of the device or compo-
nents can still be very hot and may
cause burns.
It is therefore important to observe
the following safety instructions:
Wear protective gloves during
assembly!
Disassembly of surface brush followed by
assembly of the joint brush
Switch off the device and remove the
battery (C).
Open the locking device (K) of
the guide arm (M), as shown in the
illustration.
With the lock applied (K) remove the
guide arm (M) and then the surface
brush (N).
Now open the locking device (K)
of
the drive arm (P), as shown in the illus-
tration and remove, with the lock
applied, (K) the drive arm (P) with safe-
ty guard (O).
The surface brush is now successfully
dismantled.
Put the guiding wheel (I), as shown in
the illustration, on the steering side of
the motor/gear unit (L). Now slide the
lock (K) into open position , hold
this and press the guiding wheel (I)
further onto the coupling shaft up to
the stop. Release the spring-loaded
locking device (K). The guiding wheel
(I) is locked when the locking device
independently returns to its original
position .
Put the pre-assembled joint brush
unit, as illustrated, on the drive side of
the motor/gear unit (L). Slide the lock
(K) into open position , hold this
and press the joint brush unit further
into the drive shaft up to the stop.
Release the spring-loaded locking
device (K), the joint brush unit is
locked when the locking device
independently returns to its original
posi tion .
Disassembly of joint brush followed
by assembly of the surface brush
Dismantle the joint brush according to
handling and function described above.
Open the locking device (K) of the
drive arm (P) and, with the lock
applied, (K) put the drive arm (P) with
safety guard (O), onto the drive side of
12
13
14
15
16
17
GB
RZ_MULTIBRUSH_Li-on__DE/GB/FR/NL/IT/DK_979162.qxp_Text_GB 04.03.20 17:01 Seite 31
… 30 …

Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gloria Multibrush li-on at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gloria Multibrush li-on in the language / languages: English, German, Dutch, Danish, French, Italian as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info