Manual General Electric GTD86 (page 3 of 36) (English, Spanish)

646564

Zoom out

Zoom in

1/36

 Properly ground dryer to conform with all governing codes

and ordinances. Follow details in Installation Instructions.

 Install or store where it will not be exposed to temperatures

below freezing or exposed to the weather.

 Connect to a properly rated, protected and sized power

supply circuit to avoid electrical overload.

 Remove all sharp packing items and dispose of all shipping

materials properly.

 Remove the colored protective tape from the control panel.

 Do not obstruct the flow of ventilating air. Do not stack or

place laundry or throw rugs against the front or back of the

dryer.

Steam Water Hoses:

GE strongly recommends the use of factory specified parts.

A list of factory hoses available for purchase are listed

below. These hoses are manufactured and tested to meet

GE specifications.

GE strongly recommends the use of new water supply

hoses. Hoses degrade over time and need to be replaced

every 5 years to reduce the risk of hose failures and water

damage.

Parts and Accessories

Order on-line at GEApplianceparts.com today, 24 hours a

day or by phone at 800.626.2002 during normal business hours.

Part Number Accessory

WE25M53 Complete Kit (hoses, Y-adapter

washers) (included)

WE1M847 Long hose and

WE1M849 Y-adapter

PM14X10056 Dryer door opening vent brush

(not included)

WX14X10007 LintEater™ dryer rotary tube brush

(not included)

Exhaust/Ducting:

All dryers MUST be exhausted to the outside to prevent

large amounts of moisture and lint from being blown into

the room.

Use only rigid metal 4ļ diameter ductwork inside the dryer

cabinet and use only rigid metal 4ļ diameter or UL

approved transition ducting between the dryer and the

home duct. USE OF PLASTIC OR OTHER COMBUSTIBLE

DUCTWORK CAN CAUSE A FIRE. PUNCTURED DUCTWORK

CAN CAUSE A FIRE IF IT COLLAPSES OR BECOMES

OTHERWISE RESTRICTED IN USE OR DURING

INSTALLATION.

For complete details, follow the Installation Instructions.

SAVE THESE INSTRUCTIONS

GEAppliances.com

PROPER INSTALLATION

This dryer must be properly installed and located in accordance with the Installation Instructions before it is used.

If you did not receive an Installation Instructions, you can receive one by visiting GEAppliances.com or by calling

800.GE.CARES (800.432.2737).

ADDITIONAL GAS DRYER WARNINGS

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion

or to prevent damage, personal injury, or death.

- DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch; DO NOT use any phone in your building.

• Clear the room, building, or area of any occupants.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

WARNING

State of California Proposition 65 Warnings:

The California Safe Drinking Water and Toxic Enforcement Act requires the governor of California to publish a list of substances

known to the state to cause cancer, birth defects or other reproductive harm and requires businesses to warn of potential exposure

to such substances.

WARNING

This product contains one or more chemicals known to the State of California to cause cancer, birth defects or

other reproductive harm.

Gas appliances can cause low-level exposure to some of these substances, including benzene, carbon monoxide, formaldehyde and

soot, caused primarily by the incomplete combustion of natural gas or LP fuels. Exposure to these substances can be minimized by

properly venting the dryer to the outdoors.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of General Electric GTD86 in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

General Electric GTD86 Manual

Product: