646523

General Electric DDG7980M Manual

5
Zoom out
Zoom in
Previous page
1/16
Next page
O
Fabric
Care Selections
Push
a
button
to
select the proper heat
for your load.
Should be used with cycles indicated .
Automatic,
Fabric Care
Automatic
Perm Press and
Timed
Selections
Regular Cycle
Knits Cycles
Cycles
Cottons
High Heat
●
●
Perm Press
Medium Heat
●
●
Knits/Delicates
Low Heat
●
●
Fluff
No Heat
●
~ExtraCare
Cycle
~
Select End of
Cy~le
Signal,
if
(Operates only with Automatic,
desired. (See below. )
Perm Press
&
Knits Cycles. )
Turn to ON if desired. To minimize
~
Turn Cycle Selector to desired
cycle setting. The selector may be
wrinkles set in the clothes, the Extra
Care cycle provides approximately
turned in either direction.
15 minutes of no-heat tumbling
~
Press PUSH TO START button
after the clothes are dry.
to start dryer. (Opening the door
Use End-of-Cycle Signal. Signal
during operation stops the dryer. To
will sound at five-minute intervals
re-start, close the door and press
to remind you to remove the clothes.
the START button. )
What is the difference
between
~med
&
Automatic drying?
Timed Drying
When using the TIMED CYCLES,
you select the number of minutes
you wish the dryer to run and it
turns off at the end of this time
period.
Automatic Drying
When using the Automatic Cycles,
the
El(’c’[rotli(
St’n.\t)r
Conlrol
.\?l~tt~m
continually senses the
moisture in the tumbling clothes,
determines when they are dried to
your pre-selected setting, and
terminates the cycle automatically.
Refer to the CONTROLS SETTING
GUIDE for recommended settings.
The Cycle Selector will not advance
until clothes have reached a certain
degree of dryness.
Dryness selections guide for
the automatic cycles
End-of-Cycle Signal
(Operates with any cycle. )
The Signal control can be set
anywhere between OFF and
LOUD, depending on desired
sound level. The signal will sound
just before the end of the cycle to
remind you to remove the clothes.
To stop signal while sounding, turn
Signal control to OFF or advance
Cycle Selector to OFF.
The Signal should always be used
when drying Polyester Knits or
Permanent Press items which
should be removed as soon as the
dryer stops to
help
prevent setting
of wrinkles.
The signal should also be used with
the Extra Care Cycle.
Polyester Knits &
Permanent Press
drying tips
● DO NOT
OVERLOAD—
Garments being dried or
dewrinkled should tumble freely.
. REMOVE CLOTHES
PROM~LY—To help prevent
wrinkling, remove from the dryer
promptly at the end of the drying
cycles.
. PLACE ON
HANGERS—
Permanent Press and Polyester
Knit garments look best if placed
on hangers after drying.
5
Set to Middle Position
,1, s
A“tomaf,c
,,”
Reg”la,
c”cles
.*
.*
.,”,
●
e
0,”
@
● For most normal loads.
Set toward MORE DRY
● For loads that include heavy-
weight fabrics.
● If you desire to remove more
moisture.
Set toward LESS DRY
● For lightweight fabric loads
● If you desire to remove less
moisture.
● For very small loads.
-
for
(’ontr(ds
setting
Guide
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for General Electric DDG7980M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of General Electric DDG7980M in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info