479885
3
Zoom out
Zoom in
Previous page
1/4
Next page
INSTALLER MANUAL - PAGE 05PAGE 04 - INSTALLER MANUAL
INSTALLER MANUAL
BLACK
RED
6-way connector to plug into
the free connector
on the BSI control unit
marked
“EA”
5.0 - COMPLETE ELECTRIC DIAGRAM
CAN BUS signal
LIGHT BLUE (CAN-L)
LIGHT BLUE-GREY (CAN-H)
3
1
6
4
6.0-U
6.1 - CONNECTIONS AND POSITIONING
6.2 - SENSOR ADJUSTMENT
Insert the WHITE connector
.
:
.
LTRASONIC VOLUMETRIC PROTECTION
in the the “W” socket on the control unit.
Insert the RED connector in the “R” socket on the control unit.
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the aeration inlets and orient them towards the center of the rear window
o check sensors proceed as follows
With system disarmed, roll down the front window approx. 20 cm.
Set the trimmer on the control unit to the middle position.
Close doors, bonnet and boot and arm the system.
During the system inhibit arming time, introduce an object in the cabin and move it around; the
status LED will turn off to signal a presence.
If sensibility level is too low, adjust trimmer again and repeat above procedure
!
!
!
!
!
ULTRASONIC
CELLS
CONNECTIONS
SENSIBILITY
ADJUSTMENT
4.0 - CONNECTORS TABLES
Ground
-----
Positive
-----
-----
-----
-----
-----
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-9-
-10-
-11-
-12-
-13-
-14-
-15-
-16-
-17-
-18-
-19-
-20-
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-----
-----
-----
-----
-----
-----
BROWN
BLACK
RED
-----
LIGHT BLUE-GREY
LIGHT BLUE
PINK
GREEN-BLACK
-----
-----
-----
-----
-----
----
BLACK
-----
RED
-----
-----
-----
-----
-----
WIRE FUNCTION
WIRE FUNCTION
POSITION
POSITION
WIRE COLOUR
WIRE COLOUR
4.1 - 20-WAY CONNECTOR
4.2 - 8-WAY CONNECTOR
-----
-----
-----
-----
-----
-----
Grund for external sensor connector
LED negative output
LED positive output
-----
CAN BUS signal (CAN-H)
CAN BUS signal (CAN-L)
Positive output with system armed (+A)
External sensor negative input
-----
-----
-----
-----
-----
-----
For the system to work properly, the “original alarm installed” feature (BSI unit)
must first be enabled via the specific diagnostic tester available at any authorized
Peugeot-Citroën dealer (PSA group).
Moreover, this type of system DOES NOT require that you program the vehicle
code, it is already factory-registered by Gemini.
NEVER PRESS THE PROGRAMMING BUTTON LOCATED NEXT TO THE UNIT
BUILT-IN LED
!
Before carrying out all
electrical connections,
disconnect the
negative battery
terminal and re-
connect again after
completion.
!
Red
Black
Connector for external modules
Pink
Brown
Green-Black
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 931PSA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 931PSA in the language / languages: English as an attachment in your email.

The manual is 0,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info