479883
7
Zoom out
Zoom in
Previous page
1/8
Next page
PAGE 12 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 13
11.0 - ADDING NEW DEVICES 12.0 - DELETING PROGRAMMED DEVICES
To carry out the operation successfully, make sure the required electrical connections
(door push-button, bonnet push-button and positive under key) are complete.
To carry out the operation successfully, make sure the required electrical connections
(door push-button, bonnet push-button and positive under key) are complete.
!
!
!
All device previously programmed in the memory, such as control devices, magnetic contacts,
opening detectors or infrared sensors, can be erased
To clear memory proceed as follows
With system disarmed, open the driver side door and the bonnet and leave them open!
.
.
.
!
!
!
!
!
Turn ignition key “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”.
At the fourth rotation, leave it “ON”.
.
Close the bonnet; ithe LED will be steady “ON”.
.
To confirm it has entered in the delete mode, the system gives two acoustic signals (one high and
one low-pitched)
Keep the bonnet closed (approx. 8 sec.) until the devices are completely deleted
The following operations must be carried out within four seconds otherwise the
procedure is invalidated.
!
!
.
”.
The end of the procedure is indicated by the LED turnings OFF and one long low-pitched acoustic
signal
Turn ignition key “OFF
!
50 devices.
.
Storing memory is for
If an extra device is added, it automatically deletes the first device programmed in the
system memory
!
To activate the procedure proceed as follows:
With system disarmed, open the driver side door and the bonnet and leave them open! .
!
!
!
Turn ignition key “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”.
At the fourth rotation, leave it “ON”.
.
To confirm it has entered in the self-learning mode of new control devices, magnetic contacts,
opening detectors or infrared sensors the system gives two acoustic signals (one high and one low-
pitched)
The following operations must be carried out within four seconds otherwise the
procedure is invalidated.
Do not close the bonnet otherwise all previously programmed devices are erased as
described in the next paragraph.
!
!
!
!
!
!
The system is ready to receive the device codes.
the button nr.1 of the remote,
.
.
R.
“OFF”.
T.
According to the device to be stored in memory, press insert the
electronic key into the receptacle, make the magnetic contact transmit (bring contact and magnet
close together and then move apart), press the push-button on the opening detector or make the
infrared sensor transmit (see sensor instructions)
Each time a device is learned a high-pitched signal sounds and the status LED flash briefly
epeat this procedure to program other devices
Turn ignition key
o confirm the end of the procedure a low-pitched signal sounds
!
!
If the bonnet is opened before 8 seconds, the devices will not be
deleted.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 862 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 862 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gemini 862

Gemini 862 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info