479866
2
Zoom out
Zoom in
Previous page
1/4
Next page
OPERATING DESCRIPTION
COMPLETE ALARM ARMING
Press the lock button on the original radio control of the vehicle.
Arming will be indicated by one turn signal flash and one high tone signal
(BEEP) (if these functions have not been excluded in programming stage).
AUTOMATIC ALARM ARMING
Automatic arming allows to have the alarm system active, 60 seconds after the
engine switching “OFF” and the opening of a door.
For automati arming see at the installation manual or answer to the installer.
ALARM ARMING WITH EXCLUSION OF VOLUMETRIC PROTECTION
AND COMFORT CONTROL
This function allows the user to arm the system, with volumetric protection and
comfort control being excluded
To actieve this function, the system must be disarmed and the ignition key
turned to “OFF” (is not important the position of the driver’s door).
Proceed as follows:
! Introduce the electronic key into the receptacle.
! Vehicle turn signals will flash twice to that the function has been saved to
memory.
! Press the lock button of the vehicle's original radio control.
! The system will indicate successful arming (with volumetric protection
and comfort control exclude) by one long and one shorter flashing of turn
signals and one long and one shorter beep (if these functions have not
been excluded in programming stage).
Note: this function inhibits also positive exit when alarm is armed (Pink wire),
the comfort control and the external sensor inlet (Green-Black wire) and it lasts
just for one arming cycle.
ARMING NEUTRAL TIME AND COMFORT FUNCTION
The arming neutral time lasts for 30 seconds and is indicated by permanent
turning on of the state Led.
During this period, the alarm active the comfort function for 20 seconds, and
the user is allowed to leave the vehicle without provoking any false alarm
condition.
SYSTEM ARMED
After the inhibit time (about 30 sec.), The system is armed and it is ready to
detect any theft attempt.
When the system is properly armed, the LED blinks.
After disarming the system, any occured attempt will be indicated by the alarm
with visual/acoustic signalling..
ALARM, HINIBIT TIME AND ALARM CYCLES
As previously described, any occured attempt will be indicated by the alarm
with visual/acoustic signalling.
After the alarm triggering, before another alarm cause, there are 5 seconds of
“neutral time”, that allow to disarm the system by emergency pin-code.
The alarm signalling has 10 cycles of 30 seconds each for input and arming
cycles.
The ignition key (+15/54) alarm signalling have no limitation.
ALARM DISARMING
Press the unlock button of the vehicle's original radio control.
Disarming is indicated by three turn signal flashes and three acoustic signals (if
these functions have not been excluded in programming stage).
If an alarm condition has occurred, it will be signalled by five turn signal flashes
and five acoustic signals (if these functions have not been excluded in
programming stage).
See next paragraph for all signalling.
ALARM MEMORY
When disarming the alarm, if five turn signal flashes and five beep signals
occur (if these functions have not been excluded in programming stage), it is
possible to identify the cause generating the alarm condition.
To do this, turning the ignition key in “ON” position and see at the vehicle
installed LED.
The LED will be blink, shown the last alarm condition.
The cause of the alarm will indicate for three times.
This indication can be interrupted by turning the ignition key to OFF.
PAG. 4
PAG. 5
LED SIGNAL
CAUSE OF THE ALARM
LED OFF (2 seconds) LED ON (1 second)
ALARM CYCLE
NUMBER
10
10
Infinite
10
Absorption sensor
Door, trunk and hood switches
Positive under key (+15/54)
Volumetric and external sensors
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7621 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7621 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info