544617
4
Zoom out
Zoom in
Previous page
1/4
Next page
Please read first - then do programming!!!
Before programming your TCS-Cody with your personal codes, please check the faultless
function of the appliance with the help of the factory‘s pass code 1234 and the key-operated
pushbutton.
Normally, any programming is made via your personal master code. In order to get familiar
with that kind of programming, you start with the input of a new pass code, which replaces
the one preset by the factory (1234). The procedure is explained under item
“Program 2“.
After that please change the master code to the string of digits you choose.
ATTENTION
In case you made a mistake on programming, you can start again by actuation of the key-
operated pushbutton (`*`).
Program 1
Input of a new master code
Assembly Instructions
Assembly of the CODY keyboard:
1. By slightly pushing the two latches at the right and left side of the keyboard
from behind to the edge, remove the small frame from the keyboard.
2. Now you see two fixingholes (diam. = 4 mm) at the front of the keyboard.
By means of these you can fix the keyboard onto the wall.
3. Connect the keyboard to the logic unit by means of a twin-cable (up to 5 m long).
There is no particular polarity for the twin wires.
4. Now re-fix the small frame.
5. It is possible to connect in parallel up to four keyboards if a thin connection cable, max.
total line cross-section 1.5 mm
2
, is used.
Keyboards connected in this way must not be operated simultaneously.
Assembly of the logic unit (inside area):
1. Put the screw-driver into the gap of the enclosure front, push the screw-driver up and
open the enclosure.
2. Remove the control PCB (which is force fitted to the inside of the enclosure).
3. Locate the screwed glands supplied (sealing nipple left side) in the
enclosure and replace the PCB. (Please ensure PCB is firmly in position)
4. Bore the fastening holes and fix the enclosure bracket at the wall.
5. The wires for the keyboard ensure through the left cable entry (sealing nipple), the wires
for the relay contacts through the two middle cable entries and the wires for the supply
voltage ensure through the right cable entry. Ensure tight seating of sealing nipple and
cable gland, otherwise the water-protection ot the appliance cannot be assured.
6. According to connection diagram connect the wires to the corresponding
terminals:
Connections:
Keyboard, door 1 (e.g. garage door drive), door 2 (e.g. garage door drive), supply voltage
Programming Instructions
Input 8-digit
master code
Input 8-digit
NEW master code
Sound
signal
2 x long
Push key
button
Push key
button
Sound signal
1 x long
Sound signal
1 x short
Push key
button
The new master code is now stored !
1
Spannungsversorgung
je nach Gerätetyp
Tastatur
Trafo
Generalreset
L1 N PE
Tor 1
Tor 2
Cody 1/2
Connection diagram:
keyboard
door 1
door 2
power supply
GENERAL RESET
Push Button
Trans-
former
industial controls
®
industial controls
®
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Geba Tronic TCS - Cody 1- 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Geba Tronic TCS - Cody 1- 1 in the language / languages: English as an attachment in your email.

The manual is 0,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Geba Tronic TCS - Cody 1- 1

Geba Tronic TCS - Cody 1- 1 User Manual - English - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - German - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - Dutch - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - Dutch - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - French - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - French - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - Spanish - 4 pages

Geba Tronic TCS - Cody 1- 1 User Manual - Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info