589619

Garmin Vector Manual

2
Zoom out
Zoom in
Previous page
1/26
Next page
Vector™ Quick Start Manual
WARNING
Read all instructions carefully before installing and using the
Vector™ system. Improper use could result in serious injury.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTICE
Go to www.garmin.com/vectorowner for the latest information
including bike compatibility, software updates, and video
tutorials.
Tools Needed
• 15 mm pedal wrench
• Bike grease
• 3 mm hex key
• 4 mm hex key
Installing Vector Components
Preparing the Crank Arms
1Confirm the compatibility of your bike at www.garmin.com
/vectorowner.
2Remove the existing pedals.
3Clean the threads, and remove old grease.
Determining Pedal Pod Clearance
NOTICE
The pedal pod should contact the crank arm only at its mounting
face, because this is the load-bearing connection. If the pedal
pod contacts the crank arm anywhere else, the pedal pod may
fracture when the pedal is tightened.
• If the mounting face À surrounding the threaded hole in the
crank arm is recessed, use one or two washers Á to fill the
recess.
NOTE: Do not use more than two washers.
• Make sure the pedal pod mounting face  contacts the crank
arm only at its mounting face (or the washer used to fill the
recess).
If it touches anywhere else, you can use another washer to
provide the necessary clearance.
• If it is close, you can confirm proper clearance by sliding a
piece of paper between the metal bracket and the crank arm
face.
• If the mounting face of the crank arm is protruding, do not
use washers.
Installing the Pedal Pod and Pedal
NOTE: The left and right pedal pods are the same.
1Install the left pedal first.
2Apply a thin layer of grease on the pedal spindle À and the
pedal pod Á where it contacts the pedal spindle.
3On the pedal spindle, stack the pedal pod and any required
washers Â.
TIP: You must carefully bend the cable à out of the way.
4Insert the spindle into the crank arm Ä.
5Hand tighten the spindle.
NOTE: The left pedal spindle has a left-handed (reverse)
thread.
TIP: Power and cadence calculations are not impacted by
the orientation of the pedal pod. Garmin® recommends
placement of the pedal pod on the leading edge of the crank.
When the crank is in the forward position, the pedal pod
should be pointing downward.
6Rotate the crank arm to check for clearance.
The pedal pod should not interfere with any part of the bike.
7Use the pedal wrench to tighten the spindle.
NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to
40 N-m).
8Firmly plug the cable into the spindle.
9Rotate the crank arm to check for clearance.
10Repeat steps 2–9 to install the right pedal.
NOTE: If the pedal pod cable rubs the chain, you can add
one or two washers between the pedal pod and the crank
arm to increase clearance.
Installing the Shoe Cleats
NOTE: The left and right cleats are the same.
1Apply a thin layer of grease on the cleat bolt threads.
2Align the cleat À, washers Á, and bolts Â.
3Use a 4 mm hex key to loosely attach each bolt to the sole of
the shoe.
4Adjust the cleat to the shoe in your preferred position.
This can be adjusted after a trial ride.
5Tighten the cleat firmly to the shoe.
NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-
m).
2
2 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Vector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector in the language / languages: English as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Vector

Garmin Vector User Manual - English - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info