501971
3
Zoom out
Zoom in
Previous page
1/10
Next page
GPSMAP 700 Series Installation Instructions 3
To install the bail-mount bracket without the cables routed through the bracket:
1. Using the included bail-mount bracket template, determine the best place to install the bracket. Be sure to leave adequate clearance behind
the chartplotter for the wiring.
NOTE: To avoid interference, mount the GPSMAP 700 series chartplotter at least 32 in. (813 mm) from a magnetic compass.
2. The bail-mount bracket template has adhesive on the back. Remove the protective liner and apply the template to the location at which you
want to install the bail-mount bracket.
3. Use a
1
/
8
in. (3 mm) drill bit to drill the four outer pilot holes marked on the template. Do not drill the two pilot holes marked on the cable-
organization bracket.
NOTE: If you are mounting the chartplotter in berglass, it is recommended to use a countersink bit to drill a clearance-counter bore through
only the top gel-coat layer. This will help to avoid any cracking in the gel-coat layer when the screws are tightened.
4. Remove the bail-mount bracket template from the mounting surface.
5. Secure the bail mount to the surface using the four included 35 mm M 4.2 × 1.4 screws.
NOTE: Stainless-steel screws may bind when screwed into berglass and overtightened. Garmin recommends applying an anti-galling,
stainless anti-seize lubricant to the screw before using.
To install the GPSMAP 700 series chartplotter on the bail-mount bracket:
1. Loosely attach the mounting knobs to the GPSMAP 700 series chartplotter.
2. Slide the chartplotter onto the bail mount, and tighten the mounting knobs.
Flush Mounting the Chartplotter
Hardware (included):
Flush-mount template
Four 35 mm M 4.2 × 1.4 screws
Tools required (not included):
Jigsaw
Drill and drill bits—
3
/
8
in. (9.5 mm) and
1
/
8
in. (3 mm)
Number 2 Phillips screwdriver
Center punch and hammer
File and sandpaper
To ush mount a GPSMAP 700 series chartplotter:
1. The ush-mount template is included in the product box. Trim the template and ensure it will t in the location where you want to ush mount
the chartplotter.
NOTES:
Make sure the surface on which you mount the chartplotter has adequate open space behind it to t the chartplotter and the connected
cables, and make sure to leave approximately
1
/
2
in. (13 mm) of space on the right side of the chartplotter to access the SD card door and
sun cover.
To avoid interference, mount a GPSMAP 700 series chartplotter at least 32 in. (813 mm) from a magnetic compass.
2. The ush-mount template has adhesive on the back. Remove the protective liner and apply the template to the location at which you want to
mount the chartplotter.
3. Using a
3
/
8
in. (9.5 mm) drill bit, drill a pilot hole inside the corner of the template to begin cutting the mounting surface.
4. Using the jigsaw, cut the mounting surface along the inside of the solid line indicated on the ush-mount template. Use a le and sandpaper
to rene the size of the hole.
5. If the top and bottom mounting covers are attached to the front of the chartplotter, remove them by unsnapping the covers from the sides.
6. Place the chartplotter in the hole, and make sure that the mounting holes on the chartplotter line up with the pilot holes on the ush-mount
template after cutting, sanding, and ling the hole. If they do not line up, mark the locations where the pilot holes need to be.
7. Using the center punch, indent the center of each of the mounting-hole locations.
8. Using a
1
/
8
in. (3 mm) drill bit, drill the pilot holes.
NOTE: If you are mounting the chartplotter in berglass, it is recommended to use a countersink bit to drill a clearance-counter bore through
only the top gel-coat layer. This will help to avoid any cracking in the gel-coat layer when the screws are tightened.
9. Place the chartplotter into the cutout.
10. Securely tighten the four included 35 mm M 4.2 × 1.4 mounting screws through the chartplotter into the pilot holes.
NOTE: Stainless-steel screws may bind when screwed into berglass and overtightened. Garmin recommends applying an anti-galling,
stainless anti-seize lubricant to the screw before using.
11. Install the top and bottom mounting covers by snapping them into place.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GPSMAP 721 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GPSMAP 721 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GPSMAP 721

Garmin GPSMAP 721 User Manual - English - 100 pages

Garmin GPSMAP 721 Installation Guide - German - 10 pages

Garmin GPSMAP 721 User Manual - German - 104 pages

Garmin GPSMAP 721 Installation Guide - Dutch - 8 pages

Garmin GPSMAP 721 User Manual - Dutch - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info