740401
1
Zoom out
Zoom in
Previous page
1/6
Next page
GMR Fantom
4/6
Installation Instructions
Important Safety Information
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
The radar transmits electromagnetic energy. Ensure that the
radar is installed according to the recommendations in these
instructions and that all personnel are clear of the path of the
radar beam before transmitting. When properly installed and
operated, the use of this radar conforms to the requirements of
ANSI/IEEE C95.1-1992 Standard for Safety Levels with Respect
to Human Exposure to Radio Frequency Electromagnetic Fields.
When the radar is transmitting, do not look directly at the
antenna at close range; eyes are the most sensitive part of the
body to electromagnetic energy.
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
CAUTION
This device should be used only as a navigational aid. Do not
attempt to use the device for any purpose requiring precise
measurement of direction, distance, location, or topography.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
CAUTION
Opening the pedestal may result in personal injury and/or
damage to the device. This device contains no user-serviceable
parts, and should be opened only by a Garmin
®
authorized
service technician. Any damage to the device resulting from
opening the unit by anyone other than a Garmin authorized
service technician will not be covered by the Garmin warranty.
Registering Your Device
Help us better support you by completing our online registration
today.
Go to my.garmin.com.
Keep the original sales receipt, or a photocopy, in a safe
place.
Contacting Garmin Product Support
Go to www.garmin.com/support for in-country support
information.
In the USA, call 913-397-8200 or 1-800-800-1020.
In the UK, call 0808 238 0000.
In Europe, call +44 (0) 870 850 1241.
Tools Needed
#2 Phillips screwdriver
5 mm hex wrench
Drill
15.0 mm (
19
/
32
in.) drill bit
32 mm (1
1
/
4
in.) drill bit (optional)
17 mm (
21
/
32
in.) wrench and torque wrench
3.31 mm² (12 AWG) copper wire to ground the radar housing
(the length depends on the distance from the radar to
ground)
Marine sealant
Mounting Considerations
When selecting a mounting location, observe these
considerations.
It is highly recommended that the device is mounted out of
range of people, with the vertical beam width above head
height. To avoid exposure to harmful radio frequency (RF)
levels, the device should not be mounted closer to people
than the maximum safe distance value listed in the product
specifications.
The device should be mounted high above the ship’s keel
line with minimal blockage of the radar beam. Obstructions
may cause blind and shadow sectors, or generate false
echoes. The higher the installation position, the farther the
radar can detect targets.
The device should be mounted on a flat surface or a platform
that is parallel to the vessel's water line and is sturdy enough
to support the device's weight. The weight for each model is
listed in the product specifications.
The radar beam spreads vertically 11.5° above and
11.5° below
À
the radar's radiating element. On vessels with
higher bow angles at cruise speed, the installation angle can
be lowered to point the beam slightly downward to the
waterline while at rest. Shims can be used if necessary.
The device should be mounted away from heat sources, such
as smoke stacks and lights.
The device should be mounted at a different level than
horizontal spreaders and mast crosstrees.
To avoid interference with a magnetic compass, the device
should not be mounted closer to a compass than the
compass-safe distance value listed in the product
specifications.
Other electronics and cables should be mounted more than
2 m (6.5 ft.) from the radar beam path.
GPS antennas should be either above or below the radar
beam path.
The device should be mounted at least 1 m (40 in.) from any
transmitting equipment.
The device should be mounted at least 1 m (40 in.) away
from cables carrying radio signals such as VHF radios,
cables, and antennas.
July 2017
190-01967-02_0D
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GMR Fantom 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GMR Fantom 6 in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GMR Fantom 6

Garmin GMR Fantom 6 Installation Guide - German - 6 pages

Garmin GMR Fantom 6 Installation Guide - Dutch - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info