691444
2
Zoom out
Zoom in
Previous page
1/4
Next page
2
Connect the bare-wire end of the power cable to a 12 Vdc
power source and to ground.
3
Align the notch on the end of the power cable with the power
port on the device, and press the cable into place.
4
Tighten the locking ring.
5
Repeat steps 3 and 4 for the network and transducer cables.
Installation Diagram
You can use this diagram to identify the connection points from
your sounder to the network, power, and transducer.
Item Description
À
Chartplotter
Á
GCV 10
Â
Power Source
Ã
Transducer
Cable Routing Grommets
NOTICE
Cable routing grommets do not create a waterproof seal. To
create a waterproof seal, apply a marine sealant around the
grommet and cable after installation. Be sure to test the system
before sealing the grommets.
When routing cables through your boat, it may be necessary to
drill holes to route the connector ends of the cables. A rubber
grommet is provided to cover the cable hole for a finished look.
You can purchase additional grommets from your Garmin
dealer or directly from Garmin at www.garmin.com.
Installing the Cable Grommet
1
Mark the location where you want to route the cable.
2
Using a 32 mm (1¼ in.) paddle drill bit or hole saw, drill the
installation hole.
3
Route the cable through the hole to the sounder.
4
Spread the grommet apart at the split, and place it around
the cable.
5
Firmly push the grommet into the installation hole until it is
seated.
6
Apply marine sealant, as needed, to weatherproof the
installation hole.
Blink Codes
After the sounder is installed, it turns on when the chartplotter is
turned on. The two-color (green and red) LED on the sounder
indicates its operational status.
LED
Color
State Status
Green Slow blink The sounder is connected to a chartplotter
and is operating properly. You should see
sonar data on the chartplotter.
Red Slow blink The sounder is turned on, but is not
connected to a chartplotter, or is waiting to
connect to a chartplotter. If the sounder is
connected to the chartplotter and this code
persists, check the wiring connections.
Red/
Green
Slow blink The sounder is in test mode.
Red Rapid blink
sequence
System error. The chartplotter displays a
message indicating the type of failure. When
the error condition is fixed, the sounder must
be completely disconnected from and
reconnected to its power source to clear the
error.
Specifications
Specification Measurement
Size (H×W×D) 251 x 192 x 66 mm (9.9 x 7.6 x 2.6 in.)
Weight 845 g (1.86 lb.)
Case Material Fully gasketed, polycarbonate plastic, water
resistant to IEC 60529-IPX7
Temperature Range From -15° to 70°C (from 5° to 158°F)
Power Input From 10 to 35 Vdc
Power usage 10.5 W maximum
Fuse 4.0 A, mini 42 Vdc, fast-acting, blade-type
Compass Safe
Distance
260 mm (10.2 in. )
Transmit Power (RMS)* 500 W per element (1,500 W combined)
*dependent upon transducer rating and depth
Frequency 455/800 kHz
Depth** 229 m (750 ft) down; 153 m (500 ft) side
**maximum depth, dependent upon
transducer, water salinity, bottom type, and
other water conditions
Data Output Garmin Marine Network
2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GCV10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GCV10 in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GCV10

Garmin GCV10 Installation Guide - German - 4 pages

Garmin GCV10 Installation Guide - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info