691893
1
Zoom out
Zoom in
Previous page
1/2
Next page
GC
12 MARINE CAMERA
INSTALLATION
INSTRUCTIONS
Mounting Considerations
You can mount the camera upside-down or sideways. You can
reverse the camera image to use in rearview mode. See your
chartplotter owner's manual for instructions.
You should mount the camera in a location where it is
not an obstacle in doorways or walkways.
not exposed to extreme temperatures.
not exposed to gas or oil.
not exposed to radioactivity.
not facing into direct sunlight or a direct reflection of sunlight.
Tools Needed
1 A fuse or circuit breaker
Drill and 2 mm (
1
/
16
in.) drill bit
Mounting the Camera
1
Secure the template
À
to the mounting location.
2
Using a 2 mm (
1
/
16
in.) drill bit, drill the pilot holes.
3
Adjust the dome base
Á
to the correct orientation for your
desired camera tilt.
4
Secure the dome base to the mounting location using the
included tapping screws
Â
.
5
Insert the camera
Ã
into the dome base.
6
Secure the set screws
Ä
into the dome front
Å
using the
included wrench.
Installation Considerations
You must connect the camera power wire to the battery through
a 1 A fuse or circuit breaker. If you do not use a fuse or circuit
breaker, the camera can malfunction.
Some Garmin
®
GPSMAP
®
chartplotters have a built-in CVBS
video encoder. Video from the camera or cameras appears on
all chartplotters on the network when plugged into a single
CVBS IN port. Go to www.garmin.com/manuals/gc12 for a list of
compatible GPSMAP chartplotters.
If you want to use more than one camera or the chartplotter
does not have a CVBS IN port, you must use an encoder.
You can add up to four cameras to one encoder and up to two
encoders to the Garmin Marine Network.
Installation Diagram
À
GC 12 Marine Camera
Á
1 A fuse or circuit breaker (not included)*
Â
12 Vdc Power source
Ã
BNC to BNC Coax Video Cable (not included)
Ä
Compatible Garmin chartplotter
*You must connect the camera power wire to the battery through
a 1 A fuse or circuit breaker. If you omit a fuse or circuit breaker,
the camera can malfunction.
Installation With Encoder Diagram
You can add more than one camera to your network when you
use an encoder.
À
GC 12 Marine Camera
Á
1 A fuse or circuit breaker (required, not included)*
Â
12 Vdc Power source
Ã
BNC to BNC Coax Video Cable (not included)
Ä
Network cable
Å
Power-over-Ethernet isolation coupler (GPN 010-10580-10)
Æ
Garmin Marine Network cable
Ç
Axis
®
Q7424 Encoder (optional/not included)
È
Compatible Garmin chartplotter
*You must connect the camera power wire to the battery through
a 1 A fuse or circuit breaker. If you omit a fuse or circuit breaker,
the camera can malfunction.
Troubleshooting
Video Does Not Appear on the Chartplotter Screen
Verify all cables are firmly connected.
Verify the video cable is connected to the camera video
output port.
Image on the Chartplotter Screen is Dim or Dark
Verify the lens is clean. If necessary, wipe the lens with a
soft, clean cloth.
If the camera is exposed to too much direct light, change the
camera position or location.
August 2018
190-01087-01_0A
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GC 12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GC 12 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GC 12

Garmin GC 12 Installation Guide - German - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info