691420
2
Zoom out
Zoom in
Previous page
1/4
Next page
8
Ensure the mounting holes on the device line up with the pilot
holes on the template.
9
If the mounting holes on the device do not line up with the
pilot holes on the template, mark the new pilot-hole locations
on your template.
10
Using a 3.2 mm (
1
/
8
in.) drill bit, drill the pilot holes.
11
Remove the template from the mounting surface.
12
Place the device in the cradle.
13
Install the rubber gasket on the back of the device.
The rubber gasket has adhesive on the back. Make sure you
remove the protective liner before installing it on the device.
14
Connect all necessary cables, and spin the locking rings
clockwise to secure the cables to the cradle before placing it
into the cutout.
TIP: To prevent corrosion of the metal contacts, cover
unused connectors with weather caps.
15
Place the device into the cutout.
16
Secure the device to the mounting surface using the included
screws.
17
Install the trim caps by snapping them in place around the
edges of the device.
Installing the Cables and Connectors
Connecting to Power
WARNING
When connecting the power cable, do not remove the in-line
fuse holder. To prevent the possibility of injury or product
damage caused by fire or overheating, the appropriate fuse
must be in place as indicated in the product specifications. In
addition, connecting the power cable without the appropriate
fuse in place voids the product warranty.
1
Route the power cable to the power source and to the device.
2
If necessary, extend the wires using 1.31 mm
2
(16 AWG) or
larger wire.
3
Connect the red wire to the positive (+) battery terminal, and
connect the black wire to the negative (-) battery terminal.
4
Connect the power cable to the device, and turn the locking
ring clockwise to tighten it.
Wiring Harness
The wiring harness is used for NMEA
®
0183 devices, and to
share route and waypoint information.
The wiring harness connects the device to power and NMEA
0183 devices.
The device has one internal NMEA 0183 port that is used to
connect to NMEA 0183 compliant devices.
If it is necessary to extend the power and ground wires, you
must use 1.31 mm
2
(16 AWG) or larger wire.
If it is necessary to extend the NMEA 0183 or alarm wires,
you must use .33 mm
2
(22 AWG) wire.
Item Wire Function Wire Color
NMEA 0183 internal port Rx (in) Brown
NMEA 0183 internal port Tx (out) Blue
Ground (power and NMEA 0183) Black
Power Red
Connecting the Device to a Transducer
Go to www.garmin.com/transducers or contact your local
Garmin dealer to determine the appropriate type of transducer
for your needs.
1
Follow the instructions provided with your transducer to
correctly install it on your boat.
2
Route the transducer cable to the back of your device, away
from sources of electrical interference.
3
Connect the transducer cable to the appropriate port on the
cradle.
Installing the Device in the Cradle
After the cables are connected to the cradle, you can quickly
place the device in the cradle.
1
Place the base of the device in the bottom of the cradle.
2
Tilt the top of the device toward the cradle.
3
Press the button on the release level, and push the release
lever down until the device clicks in place.
Removing the Device from the Cradle
1
Press the button on the release lever on the cradle, and pull
the lever up.
2
Tilt the device forward, and lift the device out of the cradle.
NMEA 2000
®
Considerations
NOTICE
If you are connecting to an existing NMEA 2000 network,
identify the NMEA 2000 power cable. Only one NMEA 2000
power cable is required for the NMEA 2000 network to operate
properly.
A NMEA 2000 Power Isolator (010-11580-00) should be used in
installations where the existing NMEA 2000 network
manufacturer is unknown.
2
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin ECHOMAP Ultra serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin ECHOMAP Ultra serie in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin ECHOMAP Ultra serie

Garmin ECHOMAP Ultra serie User Manual - English - 52 pages

Garmin ECHOMAP Ultra serie User Manual - German - 60 pages

Garmin ECHOMAP Ultra serie Installation Guide - German - 4 pages

Garmin ECHOMAP Ultra serie Installation Guide - Dutch - 4 pages

Garmin ECHOMAP Ultra serie User Manual - Dutch - 56 pages

Garmin ECHOMAP Ultra serie Installation Guide - French - 4 pages

Garmin ECHOMAP Ultra serie User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info