691897
3
Zoom out
Zoom in
Previous page
1/4
Next page
5
Turn on power to the sensor, and wait until the heading data
appears on the display
À
.
6
Within three minutes, complete two full, slow, tight circles
Á
,
taking care to keep the boat as steady and level as possible.
The boat should not list during calibration.
If possible, you can turn the vessel in place by engaging two
engines in opposite directions.
When the sensor is prepared to calibrate the compass, the
heading data disappears from the display
Â
.
You may receive an error message that the heading was lost.
You can ignore this message.
7
Continue turning in the same direction at the same speed
Ã
for approximately 1
1
/
2
rotations until the heading data
appears
Ä
.
When the heading data appears, the compass has been
calibrated successfully, and you can align the heading
(optional).
8
Select an option.
If you want to align the heading to match the front of the
boat, proceed to the next step.
If you installed the sensor with cable pointing toward the
bow, parallel to the keel, and do not want to align the
heading, stop turning and wait, keeping the boat
stationary. Over the next two minutes the heading data
should disappear and then reappear. When the heading
data reappears, the compass should be calibrated and no
heading offset should be applied.
NOTE: If an unwanted heading offset is applied, you must
disconnect all GPS sources from the NMEA 2000 network,
and repeat the calibration. If the only available heading
display is also a GPS source, you must repeat the
calibration, and disconnect the sensor after step 7.
9
Continue turning in the same direction at the same speed for
approximately ten seconds, until the heading data disappears
from the display
Å
.
10
When it is safe, straighten the boat and drive in a straight line
Æ
at cruising speed (must be at least 6.4 km/h (4 mph)) until
the heading data appears
Ç
.
When the heading appears, the compass has been
calibrated, and the heading has been aligned on the sensor.
11
Test the results of the calibration, and repeat this procedure if
necessary.
Restoring Factory Default Settings
If you relocate the sensor or do not believe the calibration was
successful, you can delete all calibration information from the
sensor, and restore its factory default settings. After restoring
the factory default settings, you must configure the sensor
before you can use it with your system.
1
Select Settings > Communications > NMEA 2000 Devices
> Device List.
2
Select the name of the sensor.
3
Select Review > Factory Defaults > Yes.
Specifications
Specification Measurement
Dimensions (L × W × H) 170 × 90 × 50 mm (6.7 × 3.5 × 2 in.)
Weight 200 g (7 oz.)
Temperature range From -15° to 70°C (from 5° to 158°F)
Material Fully gasketed, high-impact plastic
Water resistance IEC 60529 IPX7*
NMEA 2000 input voltage From 9 to 16 Vdc
NMEA 2000 LEN 4 (200 mA)
Compass-safe distance Negligible
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to www.garmin.com
/waterrating.
Limited Warranty
The Garmin standard limited warranty applies to this accessory.
For more information, go to www.garmin.com/support/warranty
.html.
© 2017 Garmin Ltd. or its subsidiaries
Garmin
®
and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries,
registered in the USA and other countries.
NMEA 2000
®
and the NMEA 2000 logo are registered trademarks of the National Marine
Electronics Association.
3
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin 9 axis Heading Sensor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin 9 axis Heading Sensor in the language / languages: English as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin 9 axis Heading Sensor

Garmin 9 axis Heading Sensor Installation Guide - German - 4 pages

Garmin 9 axis Heading Sensor Installation Guide - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info