760879
30
Zoom out
Zoom in
Previous page
1/32
Next page
30
en Trouble shooting
3
Trouble shooting
Trouble shooti ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Display Possible cause Solution
None The power supply has been disconnected. Use other electrical appliances to check whether a
short circuit has occurred in the power supply.
The appliance has not been connected as
shown in the circuit diagram.
Make sure that the appliance has been connected as
shown in the circuit diagram.
Electronics fault. If the fault cannot be rectified, inform the technical after-
sales service.
An audible signal sounds The control panel is wet or an object is cov-
ering it.
Dry the control panel or remove the object.
The hotplate has been
switched off. The illumi-
nated ring on the control
knob is flashing.
The control knob has not been turned for
an extended period. The automatic safety
cut-out function has been activated.
Turn the control knob to position 0. Switch the hotplate
back on.
The appliance is too hot. Read the fault message on the control panel.
The hotplate indicator is
flashing.
The cookware is not being detected. Make
sure that the cookware is suitable for use
with an induction hob.
Make sure that the diameter of the base of the cook-
ware corresponds to the size of the hotplate. Turn the
control knob to position 0. Switch the hotplate back on.
”ƒ The electronics have overheated and the
affected hotplate has been switched off.
Remove any cookware from the hob. Once the fault
code goes out, the hotplate has cooled down suffi-
ciently. Turn the control knob to position 0. Then select
the heat setting as usual.
”… The electronics have overheated and all
hotplates have been switched off.
Ӡ + heat setting and sig-
nal tone
There is hot cookware near the control
panel. There is a risk that the electronics
will overheat.
Remove the cookware. The fault code goes out shortly
afterwards. You can now resume cooking.
Ӡ and signal tone There is hot cookware near the control
panel. The cooking zone has been
switched off to protect the electronics.
Remove the cookware. Wait a few seconds. When the
fault code on the display goes out, you can resume
cooking.
”‚ / ”‡ The hotplate has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently
before switching the hotplate on again.
”‰ The hotplate has been operating continu-
ously for an extended period.
The automatic safety cut-out function has been acti-
vated. See section ~ "Locking the control panel
for cleaning".
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect/outside
of the normal operating range.
Contact your energy supplier.
—…‹‹ The hob is not connected correctly Disconnect the hob from the mains. Make sure that it
has been connected as shown in the circuit diagram.
Do not place hot cookware on the control panel.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gaggenau VI422113 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gaggenau VI422113 in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gaggenau VI422113

Gaggenau VI422113 User Manual - German - 32 pages

Gaggenau VI422113 User Manual - Dutch - 32 pages

Gaggenau VI422113 User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info