678947
1
Zoom out
Zoom in
Previous page
1/2
Next page
FD-110 Installation
Outdoor-unit:
Indoor-unit:
Important Note:
If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
Recycle used batteries following environmental protection practices.
Transmitter Installation:
Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
Recycle used batteries following environmental protection practices.
Transmitter Installation:
Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Connecting:
Important Note:
If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
Recycle used batteries following environmental protection practices.
Transmitter Installation:
Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1
Accessories List:
1 x Receiver 1 x Transmitter
1 x User Manual 1 x Double-sided adhesive
1 x 3 volts CR2032 battery for transmitter
Technical Specification:
Frequency: 433.92MHz+100KHz
Modulation Type: ASK
Ring Volume:85dB(within 0.5m)
Channel space: 1 million sets of auto-learning codes
Receiver bandwidth: ±90KHz
Reception Sensitivity:-105dBm
Transmitter Power:10mW
Power consumption(Receiver): standby:0.3W
Power consumption(Transmitter): standby:5uA working:10mA
Power Supply(Receiver): AC110-240V
Power Supply(Transmitter): DC 3V (1x CR2032)
Operating Range:150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
3 sec.
1
Accessories List:
1 x Receiver 1 x Transmitter
1 x User Manual 1 x Double-sided adhesive
1 x 3 volts CR2032 battery for transmitter
Technical Specification:
Frequency: 433.92MHz+100KHz
Modulation Type: ASK
Ring Volume:85dB(within 0.5m)
Channel space: 1 million sets of auto-learning codes
Receiver bandwidth: ±90KHz
Reception Sensitivity:-105dBm
Transmitter Power:10mW
Power consumption(Receiver): standby:0.3W
Power consumption(Transmitter): standby:5uA working:10mA
Power Supply(Receiver): AC110-240V
Power Supply(Transmitter): DC 3V (1x CR2032)
Operating Range:150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
Important Note:
If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
Recycle used batteries following environmental protection practices.
Transmitter Installation:
Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fysic FD-110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fysic FD-110 in the language / languages: All languages as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info