747956
1
Zoom out
Zoom in
Previous page
1/2
Next page
Usage condition for conventional system output
(Ch1-3) on "High Speed mode"
󾛽
CAUTION
The "High Speed mode" accept the digital servos only or
most type of peripherals.
s)FANANALOGSERVOISCONNECTEDTOTHESEOUTPUTSITWILLCAUSE A
MALFUNCTION0LEASECHECKTHEPERIPHERALSIFTHEREISAMALFUNCTIONFULL
STICKMOVEMENT)FTHEREISAMALFUNCTIONCHANGETHERECEIVERBACKTO
"Normal mode."
Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system
R6303SB
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system
S.BUS port and 3 channels for conventional system
High-Speed receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model number R6303SB,
complies with part15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
5303S% SpeciÀcations
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port and 3 channels for
conventional system/high-speed receiver
'ual antenna diversity
6i]e 08 [ 17 [ 037 in ( [ 37 [ 3 mm)
:eight 0 o] (7g)
3oZer reTuirement 379 to 79(9oltage range 3 to 89)
%e sure that Zhen using (6&s regulated output the capacity of the (6& must meet your usage
condition
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't
work properly when other type battery is used.
7he fail safe function can Ee set for each channel Zhen on Multi-ch mode hoZever it differs
according to the transmitter :hen on 7ch mode the fail safe function can Ee set for 3-channel
only
* S.BUS port 53036% can Ee used up to 7 channels or less on the 7ch mode and 1 channels
'*1/ or less on the 8ch/10ch/Multi-ch mode hoZever it differs according to the transmitter
Thank you for purchasing a Futaba R6303SB FASST -2.4GHz receiver.
The R6303SB has an S.BUS system output port and 3 conventional
system channel outputs. It can also be used with conventional system
servos, etc. in addition to S.BUS system compatible servos and gyros,
etc. When the linking procedure is performed, R6303SB recognizes the
signal mode (FASST-2.4GHz 7ch mode or 8ch/10ch/Multi-ch mode)
automatically.
The R6303SB can change the output CH from seven groups (CH group
table).
In addition, the operating mode (high-speed mode/normal mode) can be
selected.
󾛽
WARNING
$ONOTPERFORMTHE,INKINGPROCEDUREWITHTHE
MOTORPOWEREDUP4HISCOULDRESULTINSERIOUS
INJURY
/NCETHE,INKINGPROCESSISCOMPLETEDPLEASE
CYCLETHEPOWERTOTHERECEIVERTOMAKESURETHAT
ITISLINKEDANDUNDERTHECONTROLOFTHE4RANSMITTER
Link to the Transmitter
1
0RESSANDHOLDTHELink/ModeBUTTONBETWEENAND
seconds.
Re-adjust the 3CH F/S position (only for TM-8)
1
0RESSANDHOLDTHELink/ModeBUTTONBETWEENAND
seconds.
0 to 1 sec. 1 to 2 sec. 2 to 5 sec. More than 5 sec.
0 sec. 1 sec. 2 sec.
Press and Hold
No function
With TM-8
(not included in this set)
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
Other than TM-8
(not included in this set)
Re-link(ID set)
CH change mode
CH change mode
5 sec.
Power Source Precautions
It is not recommended to use a power source of less then 4.0V.
However if less than 4.0V is used please keep in mind the conditions
below..
s4HE &AIL3AFE &UNCTION-534BE SETTO/&&SINCEIT WILLDISTURBTHE
normal operation of the receiver.
s0LEASE MAKESURETHATTHEFULLYLOADED CONDITION ON THE %3# AND THE
3ERVOSWILLNOTDISTURBNORMALRECEIVER OPERATIONBEFORETHESTART OF
YOURmIGHT
4HISIS6%29 )MPORTANTONCETHE VOLTAGEDROPSBELOW VOLTSTHE
RECEIVERWILLNOLONGERCONTINUETOOPERATE
s0LEASE BE SURE THAT EVERYTHING ON CONTINUES TO WORK CORRECTLY ALL THE
WAYDOWNTOVOLTSIE3ERVOS%3#
The input voltage must not exceed the servo rating or 8.4V which ever
is lower.
Antenna installation precaution
󾛽
WARNING
"ESURETHATTHETWOANTENNASAREPLACEDATDEGREESTO
each other.
s&UTABAgS DUAL ANTENNA DIVERSITY OR $!$ THEN SEAMLESSLY SELECTS THE
BEST SIGNAL RECEPTION BETWEEN THESE ANTENNAS TO ENSURE THAT THERE IS
no loss of signal.
Antenna installation for carbon fuse
󾛽
WARNING
4HELASTMMOFTHEANTENNATIPMUSTBEFULLYEXPOSED
s0LEASE MAKESURETHAT THE EXPOSEDPORTIONWILLNOT BE ABLETO
SLIDEBACKINSIDETHEAIRCRAFTBYANYFORCESDURINGmIGHT
(Antenna installation)
90˚
Link/Mode button
LED
R6303SB
s0ORT)NITIALSETTINGISTHE#HANNEL
s0ORT)NITIALSETTINGISTHE#HANNEL
s#HANNELOUTPUTFORCONVENTIONALSYSTEM"ATTERY
terminal
sS.BUS0ORT
#ONNECTORS
1M3117
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R6303SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R6303SB in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info