747955
1
Zoom out
Zoom in
Previous page
1/2
Next page
Usage condition on "High Speed mode"
CAUTION
When using the high-speed mode, use a Futaba
digital servo (including brushless servo) or S.BUS servo
at conventional system use channels 1 to 6. Analog
servos cannot be used.
The use of analog servos may cause servo trouble.
When using analog servos, select the normal mode, and
use channel outputs 7 and 8.
Applicable systems:
T8FG 2.4GHz
(on 8ch mode)
, TM8
(on 8ch mode)
, T10CG 2.4GHz
(on
10ch mode)
, TM10
(on 10ch mode)
, TM14
(on multi-ch mode)
R6208SB
S.BUS compatible/FASST-2.4GHz (Multi-ch) system
8 channels/high-speed receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation, model number
R6208SB, complies with part15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
56%6SHFLÀFDWLRQV
S.BUS compatible/FASST-2.4GHz (Multi-ch) system/8 channels/
high-speed receiver
• Dual antenna diversity
• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
• Weight: 0.49 oz. (13.8g)
• Power requirement: 3.7V to 7.4V
(Voltage range: 3.5 to 8.4V)
* Be sure that when using ESC's regulated output the capacity of the ESC
must meet your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
Thank you for purchasing a Futaba
R6208SB
S.BUS
compatible receiver.
The
R6208SB
has an
S.BUS
system output port and a
conventional system channel output. It can also be used with
conventional system servos, etc. in addition to
S.BUS
system
compatible servos and gyros, etc.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
* However, channel outputs 7 and 8 for conventional system oper-
ate in the normal mode even if set to the high-speed mode.
Link/Mode
switch
LED
R6208SB
DATA
port
• Channel outputs
for conventional
system (
1
to
8
)
Battery terminal (
B
)
S.BUS
Port (
S.BUS
)
S.BUS
8CH/Battery(8/B)
8CH/Battery(8/B)
7CH
7CH
S.BUS connector insertion precaution
DANGER
Do not insert a connector, as shown right.
• It will occur short-circuit, by inserting this way. A short
circuit across the battery terminals may cause abnormal
heat, fire and burning.
What is S.BUS?
Different from conventional radio control systems the
S.BUS
system uses data communication to transmit control signals from
a receiver to a servo, gyro, or other
S.BUS
compatible device. This
data includes commands such as “move the channel 3 servo to
15 degrees, move the channel 5 servo to 30 degrees” to multiple
devices. The
S.BUS
devices execute only those commands for their
own set channel. For this reason, it can be used by connecting
multiple servos to the same signal line.
[Connection by S.BUS system]
*
Can also be used together with conventional servos.
*
When using servos with a remote battery pack, use S.BUS Hub
with Cable (2-way/remote battery pack use).
Please refer to the instruction manual of S.BUS Hub with Cable
(2-way/remote battery pack use) for the connection method.
S.BUS hub S.BUS hub
S.BUS output
S.BUS
Ch output/
Battery terminal
R6208SB
Battery
S.BUS servo
Conventional
servo
2ch 4ch
3ch 5ch
6ch
Do not insert either a switch
or battery in this manner.
5HFHLYHU
DANGER
1M23N17476
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R6208SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R6208SB in the language / languages: English as an attachment in your email.

The manual is 0,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info