747953

Futaba R6106HF Manual

1
Zoom out
Zoom in
Previous page
1/1
Next page
Usage condition on "High
Speed mode"
ｎ
CAUTION
ｊ
The "High Speed mode"
accept the digital servos only
or most type of peripherals.
s)FANYANALOGSERVOSCONNECTEDTOTHESE
output as it will cause malfunction.
Please check the peripherals if there's
any malfunction with whole stick lever
THROW )F ANYMALFUNCTIONOCCURPLEASE
change the operation mode to "Normal
mode."
R6106HF
For parkflight or indoor use airplanes.
For electric helicopters up to 1000mm of main rotor diameter.
R6106HFC
For small size airplanes such as wing span of up to around 1300mm.
For carbon fuse such as non powered sail planes.
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of
America, model number R6106HF/R6106HFC,
complies with part15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2) This device must accept any interference
received, including interference that may cause
undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
TEL (217)398-0007 or E-mail: service@futaba-rc.com (Service)
R6106HF/R6106HFC Specifications
FASST-2.4GHz system 6-channel receiver
• Power requirement: 3.3V~8.5V regulated output
from ESC, etc. (*1)
• Battery F/S voltage: 3.8V
•
Size: 0.85 x 1.53 x 0.48 in. (21.7 x 38.8 x 12.3 mm)
• Weight: 0.24 oz. (6.7g)/0.25 oz. (7.1g)
(*1) Be sure that when using ESC's regulated output
the capacity of the ESC must meet your usage
condition.
Re-adjust the F/S position (only
for TM-7/TM-8)
1
Press and hold the Link/Mode switch
between one(1) and two(2) seconds.
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold time
No function
With TM-7, TM-8
To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function
With TM-10, TM-14,
6EX, 7C, etc.
Re-link(ID set)
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
-. ©&54!"!#/20/2!4)/.
Operation Mode Select
The operation mode is on "Normal mode" from
factory shipping. When to change the mode,
please follow the steps shown below.
1
Turn off the receiver.
2
Press and hold the link/mode switch and
turn on the receiver. Keep the switch hold
more than one(1) second. The LED starts
flashing with the current status.
3
Release the switch.
4
Turn off the receiver.
By doing this step, the mode can switch over
between two(2) modes.
0 to 1 sec. More than 1 sec.
0 sec. 1 sec.
Press and Hold time
Turn on the receiver.
No function
Showing the CURRENT
mode with blink.
Red Blink = Normal
Green/Red Blink =
High Speed
Solid as the mode changed.
Red Solid = Normal
Green/Red Solid = High
Speed
(Become Red after one (1)
second)
㧔Function㧕
To change the mode between
Normal and High Speed
㧔LED
Status㧕
Please check the operation mode by observing
the LED when turning on the receiver. If possible
there's no FASST transmitter turned on around you
in order to make firmer check.
When turn on the receiver, the LED will be;
s2EDWHENON.ORMALMODE
s'REENAND2EDMAKES/RANGEWHENON(IGH
3PEEDMODE!FTERTWOSECONDSCHANGETO2ED
If there are some FASST transmitter turned on
around the receiver, the LED may show the above
status for a brief moment then changed to the
status indication as shown in the "LED indication"
table.
LED Indication
'REEN Red Status
Solid Solid )NITIALIZING
Off Solid No signal reception
Solid Off Receiving signals
Blink Off 2ECEIVINGSIGNALSBUT)$ISUNMATCHED
Link to the transmitter
1
Press and hold the Link/Mode switch more
than two(2) seconds.
ｎ
WARNING
ｌ
Do not perform the linking procedure
with motor's main wire is connected
or the engine is operating as it may result in
serious injury.
ｊ
7HILETHELINKINGISDONEPLEASE
cycle receiver power and check if
the receiver to be linked is really under the
control by the transmitter to be linked.
Thank you for purchasing the
R6106HF
,
R6106HFC
FASST receiver. These models have
two(2) operation mode as shown below.
Normal mode/High Speed mode
The "Normal mode" accepts any type of servos
or the peripherals as the frame rate of the output
is 16ms. The "High Speed mode" only accept
the digital servos, including BLS series, and
most peripheral equipments such as the gyros or
brushless ESCs. The frame rate of the outputs is
8ms.
The
R6106HF
,
R6106HFC
are compatible with
the FASST transmitters as shown below.
T6EX-2.4GHz, T7C-2.4GHz, TM7,
T8FG-2.4GHz, TM8, T10CG-2.4GHz
,
TM10,
TM14 (on 7ch-mode)
LED
Link/Mode Switch
R6106HF
R6106HFC
LED
Link/Mode Switch
Antenna
Antenna
Antenna installation for carbon fuse
(R6106HFC)
ｎ
WARNING
ｊ
4HEANTENNA PORTIONOFMMTIP
must be fully exposed.
s
Please make sure that the exposed portion won't
be slided back in the fuse by the wind pressure
or other force during the flight session.
Usage precautions about the power source
We do not recommend to use the power source of less
THAN6BUTIFTOUSETHELOWERVOLTAGESOURCEPLEASE
keep in mind the condition shown below.
s&AIL3AFEFUNCTION-534BEINOFFSINCETHEBATTERYFSWILL
disturb the normal operation.
s0LEASEMAKESURETHATTHEFULLLOADEDCONDITIONOFTHE%3#
and the servos won't disturb the receiver operation before
start flight.
This is very important since the receiver will stop operation
WHENTHESUPPLYVOLTAGEDROPSTOAROUND6
s0LEASE BE SURE THAT THE %3# OR SERVOS CAN KEEP mAWLESS
operation till such a lower voltage.
)FTHESERVOgSMAXIMUMVOLTAGERATINGISLESSTHAN6
the power source voltage must not exceed the servo's
rating.


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R6106HF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R6106HF in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info