747948
1
Zoom out
Zoom in
R2104GF
S-FHSS/FHSS-2.4GHz system
(Auto Detection),
4-channel receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model number R2104GF, complies
with part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
Thank you for purchasing the
R2104GF
receiver.
The
R2104GF
is designed for use with the Futaba
S-FHSS
or
FHSS
system transmitter. The
S-FHSS
system has two(2) operation mode as shown below.
s.ORMALMODE(IGH3PEEDMODE
The "Normal mode" accepts any type of servos
or the peripherals as the frame rate of the output
is 13.6ms. The "High Speed mode" only accepts
the digital servos, including BLS series, and most
peripheral equipments such as the brushless ESCs.
The frame rate of the outputs is 6.8ms.
Please pay special attention to the information
contained within this manual and transmitter's
manual in order to have a pleasant running/ying
experience.
The
R2104GF
is compatible with the
S-FHSS
or
FHSS
system transmitters as shown "Transmitter
and Receiver Compatibility".
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1M23N17432 ©FUTABA CORPORATION 2010, 8 (1)
2'&3PECIlCATIONS
(
S-FHSS/FHSS
system, 4-channel receiver)
s2ECEIVINGON'(ZBAND
s3YSTEM
S-FHSS/FHSS
SYSTEMAUTODETECTION
s/PERATIONMODE.ORMAL(IGHSPEEDAUTODETECTION
s0OWERREQUIREMENT6OR6SHAREDWITHSERVO
s#URRENTDRAINM!ATNOSIGNAL
s3IZEXXvXXMM
s7EIGHTOZG
WARNING
.%6%2USEDRYBATTERIESFOR
THEPOWERSUPPLYOFTHER2104GF
ASTHEYMAYCAUSEDIFlCULTIES
Link Procedure
Each transmitter has an individually assigned,
unique ID code. In order to start operation, the
receiver must be linked with the ID code of the
transmitter with which it is being paired. Once the
link is made, the ID code is stored in the receiver
and no further linking is necessary unless the
receiver is to be used with another transmitter.
1
0LACETHETRANSMITTERANDTHERECEIVERCLOSE
TOEACHOTHERWITHINONEMETER
2
4URNONTHETRANSMITTERANDTHERECEIVER
3
0USHANDHOLDTHE,INKSWITCHONTHE
RECEIVER
4
7HENTHELINKISCOMPLETETHE,%$ONTHE
RECEIVERCHANGESTOSOLIDGREEN
0LEASE REFER TO THE TABLEBELOWFOR ,%$ STATUS
ANDRECEIVERCONDITION
.OSIGNALRECEPTION 2ED/N
2ECEIVINGSIGNALS 'REEN/N
2ECEIVINGSIGNALSBUT)$
ISUNMATCHED
'REEN"LINK
)F THERE ARE MANY
S-FHSS/FHSS
SYSTEMS TURNED
ONAROUNDYOURRECEIVERITMIGHTNOTLINKTOYOUR
TRANSMITTER )NTHISCASE EVEN IFTHERECEIVERS
,%$STAYSSOLIDGREENUNFORTUNATELYTHE
RECEIVERMIGHTHAVEESTABLISHEDALINKTOONEOF
THE OTHER TRANSMITTERS 4HIS IS VERY DANGEROUS
IFYOU DO NOTNOTICETHISSITUATION )N ORDERTO
AVOIDTHEPROBLEMWESTRONGLYRECOMMEND
YOUTO DOUBLECHECKWHETHERYOURRECEIVERIS
CONTROLLED BY YOUR TRANSMITTER BY GIVING THROTTLE
INPUTETCANDTHENCHECKINGSERVORESPONSE
WARNING
!FTERTHELINKINGISDONEPLEASE
CYCLERECEIVERPOWERANDCHECKIF
THERECEIVERTOBELINKEDISREALLYUNDERTHE
CONTROLBYTHETRANSMITTERTOBELINKED
$ONOTPERFORMTHELINKINGPROCEDURE
WITHMOTORgSMAINWIRECONNECTEDOR
WITHTHEENGINEOPERATINGASITMAYRESULTIN
SERIOUSINJURY
FHSS-2.4GHz/S-FHSS-2.4GHz System
Transmitter and Receiver Compatibility
Transmitter
&(33
2ECEIVER
3&(33&(33
2ECEIVER
R603GF
R2004GF
R2104GF
40,'&(33 Okay Okay
&3FUNCTION#H
40,'&(33 Okay Okay
&3FUNCTION#H
49&'&(33 Okay Okay
40,'
3&(33
(IGH3PEED
Okay
&3FUNCTION!LLCHANNELS
"&3FUNCTION#H
$IGITALSERVOONLYAT(IGH3PEED
MODE
.ORMAL
&(33 Okay Okay
&3FUNCTION#H
Link switch LED
Ch output (1 to 4)
Battery terminal (B)
/PERATING0RECAUTIONS
/NCETHE
R2104GF
DETECTSTHE
S-FHSS
NORMALMODE
S-FHSS
HIGHSPEED
MODEOR
FHSS
MODETHEDETECTED
MODEISLOCKEDASLONGASTHE POWER
IS/.7HENNEEDTOCHANGETHE
MODEPLEASECYCLEPOWER
.OTE&UTABA
FHSS/S-FHSS
SYSTEMAND
FASST
SYSTEMARENOTCOMPATIBLEEACHOTHER
Usage condition on "High Speed mode"
CAUTION
7HENUSINGTHEHIGHSPEEDMODEUSEA
&UTABADIGITALSERVOINCLUDINGBRUSHLESS
SERVO!NALOGSERVOSCANNOTBEUSED
s4HEUSEOFANALOGSERVOSMAYCAUSESERVOTROUBLE


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba R2104GF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R2104GF in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info