Manual Futaba R202GF (page 1 of 1) (English)

747964

1

Zoom out

Zoom in

Previous page

1/1

Next page

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation, model number R202GF, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@hobbico.com (Support)

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2015, 5 (1)

R202GF Speciﬁcations:

(

S-FHSS/FHSS

system, 2-channel receiver)

• Receiving on 2.4GHz band

• System:

S-FHSS/FHSS

system (auto detection)

At

S-FHSS

Normal/High speed mode (auto detection)

•

Operating voltage(Typ.): 4.8V-7.4V(

shared with servo)

• F/S and Battery F/S function: The operation channels differ according to the transmitter used. However, Battery

F/S doesn't function when it is used with FHSS and F/S becomes only CH2.

• Battery F/S voltage: 3.8V

• Current drain: 30mA (at no signal)

• Size: 0.9x1.4x0.4” (23x35x9mm)

• Weight: 0.2 oz. (6g)

*

The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work

properly when other type battery is used.

WARNING

NEVER use dry batteries for the

power supply of the R202GF as they

may cause difﬁculties.

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

1

Place the transmitter and the receiver close

to each other within half (0.5) meter

2

Turn on the transmitter and the receiver.

3

Push and hold the Link switch on the

receiver.

4

When the link is complete, the LED on the

receiver changes to solid green.

* Please refer to the table below for LED status

and receiver condition.

No signal reception LED: Off

Receiving signals LED: On

Receiving signals, but ID

is unmatched.

LED: Blink

Power On, when F/S

sets it.

LED: Early

Blink the ﬁrst

one second

* If there are many

S-FHSS/FHSS

systems turned

on around your receiver, it might not link to your

transmitter. In this case, even if the receiver’s

LED stays solid green, unfortunately the

receiver might have established a link to one of

the other transmitters. This is very dangerous

if you do not notice this situation. In order to

avoid the problem, we strongly recommend

you to double-check whether your receiver is

controlled by your transmitter by giving throttle

input, etc. and then checking servo response.

WARNING

After the linking is done, please cycle

receiver power and check if the receiver

to be linked is really under the control by the

transmitter to be linked.

Do not perform the linking procedure

with motor's main wire connected or

with the engine operating as it may result in

serious injury.

Link switchLED

Battery terminal (B)

CH output (1 / 2)

Operating Precautions:

Once the

R202GF

detects the

S-FHSS

normal mode,

S-FHSS

high speed

mode or

FHSS

mode, the detected

mode is locked as long as the

power is ON. When need to change

the mode, please cycle power.

Note:

The R202GF is compatible with the S-FHSS or FHSS

system transmitters .

*Futaba S-FHSS/FHSS system does not work with current Futaba FASST/T-FHSS

system.

Usage condition on "High Speed mode"

CAUTION

When using the high-speed mode, use a Futaba digital

servo (including brushless servo). Analog servos

cannot be used.

• The use of analog servos may cause servo trouble.

1M23N17486

S-FHSS/FHSS-2.4GHz

system

(Auto Detection),

2-channel receiver

Thank you for purchasing the

R202GF

receiver.

The

R202GF

is designed for use with the Futaba

S-FHSS

or

FHSS

system transmitter. The

S-FHSS

system has two(2) operation mode as shown below.

•Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the

peripherals as the frame rate of the output is 13.6ms.

The "High Speed mode" only accepts the digital

servos, including BLS series, and most peripheral

equipments such as the brushless ESCs. The frame

rate of the outputs is 6.8ms. However, there is a

transmitter that cannot correspond, too.

Please pay special attention to the information

contained within this manual and transmitter's manual

LQRUGHUWRKDYHDSOHDVDQWUXQQLQJÀ\LQJH[SHULHQFH

The R202GF is compatible with the S-FHSS or FHSS

system transmitters

R202GF

1

R202GF when working in boat was removed and stored for a year. On replacement in boat R202GF will not link up Submitted on 19-8-2022 at 04:34
Reply Report abuse
R202GF inworking order was removed and stored for a year but does not link when back in control position Submitted on 19-8-2022 at 04:31
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

Register

Register getting emails for Futaba R202GF at:

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Futaba R202GF in the language / languages: English as an attachment in your email.

The manual is 0,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info