Applicable systems: Futaba S-FHSS/FHSS-2.4GHz system and TM-FH RF Module
R2008SB
S-FHSS/FHSS-2.4GHz System
S.BUS Port and 8 Channels for Conventional System
Receiver
R2S% SpeciÀcations
S-FHSS/FHSS-2.4GHz system/S.BUS port and 8 channels for conventional system receiver
• Dual antenna diversity
• Size: 0.98 x 1.69 x 0.55 in. (24.9 x 42.8 x 14.0 mm)
• Weight: 0.34 oz. (9.5g)
• Power requirement: 4.8V to 7.4V
• Battery F/S Voltage: 3.8V
* Be sure that when using ESC's regulated output the current capacity of the ESC must meet your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work properly when other type battery is used.
* The fail safe function can be set for each channel , however it differs according to the transmitter. When you use TM-FH RF Module , the fail safe function can be set
for 3-channel only.
* S.BUS port: R2008SB can be used up to 8 channels, however, it differs according to the transmitter. An unused channel is a neutral signal. The F/S setting channel at
F/S is F/S position
.
Another, it is Hold signal.
Thank you for purchasing a Futaba R2008SBS-FHSS/FHSS-2.4GHz compatible receiver.
The R2008SB has an S.BUS system output port and a conventional system channel outputs. It can also be used with
conventional system servos, etc. in addition to S.BUS system compatible servos and gyros, etc.
signal reception and promote safe modeling Futaba has
adopted a diversity antenna system. This allows the
receiver to obtain RF signals on both antennas and fly
problem-free.
Antenna installation for carbon fuse
WARNING
The antenna portion of 30mm tip must be fully
exposed.
• Please make sure that the exposed portion won't be slided
back in the fuse by the wind pressure or other force during
the flight session.
S.BUS connector insertion precau-
tion
DANGER
Do not insert a
connector, as shown
right.
• It will occur short-circuit, by
inserting this way. A short
circuit across the battery
terminals may cause
abnormal heat, fire and
burning.
Usage precaution
• Futaba S-FHSS/FHSS system does not work with cur-
rent Futaba FASST system. Futaba FASST system and
S-FHSS/FHSS system are not compatible each other.
WARNING
Wrap the receiver with something soft, such as
foam rubber, to avoid vibration. Moreover, The receiver
must not get wet.
Keep away from conductive material to avoid the
short circuit.
Antenna installation precaution
Do not cut or bundle the receiver antenna wire.
Do not bend the coaxial cable . It causes damage.
The antenna should not be pulled.
Keep the antenna away from the motor, ESC and
other noise sources as you can.
Be sure that the two antennas are placed at 90
degrees to each other.
• The R2008SB has two antennas. In order to maximize
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Futaba R2008SB at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Futaba R2008SB in the language / languages: English as an attachment in your email.
The manual is 0,18 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
