747973

Futaba GY440 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
Features of GY440
Set Contents
Connecting the GY440
Connecting the GY440 (S.BUS)
Mounting to Fuselage
Rudder Servo Linkage Check
The following items are supplied with the GY440:
Functions
Mini screwdriver
Sensor tape
Extension Cord: (Black)
Extension Cord: (Red)
Wiring strap
GY440
Monitor LED display
State Color Move Reference
1. No servo pulse /
sensor error
Red Slow blink
2. Warm-up Green Fast blink
3. Sensor initialization Red/Green ON
AVCS (Red)
Normal (Green)
4. Turn Red/Green Fast blink
Right (Green)
Left (Red)
5. Neutral offset Orange Slow blink Stick operation
6. Gain off
−
OFF
7. Switch operation Green One blink
Each time of switch
operation
8. Low battery Red One flash Less than 3.8V
● Remote gain function and mode switching function
You can adjust gain from the transmitter by using the remote gain
function. Gain can also be adjusted with the trimmer on the GY440.
The mode switching function allows AVCS/NORMAL gyro mode
switching.
● Integrated, compact,and light weight
Compact size
（
20.5x20.5x11mm
）
and light weight
（
3.7g
）
realized by high density mounting technology.
● Easy setup
The GY440 can be used immediately with minimum setup.
● Supporting the S.BUS/S.BUS2 connection
Only one wire connection to the receiver can operate the GY440.
I
NSTRUCTION
M
ANUAL
I
NSTRUCTION
M
ANUAL
Rate Gyro for Helicopters
For RC models
●
Trimmer
（
Limit / Gain
）
●
LED
●
Servo Selection Switch
●
Port1
（
Rudder input/S.BUS input
）
●
Port2
（
Gain input
）
●
Port3
（
Rudder output
）
●
Gyro Direction
Switch
WARNING
Failure to follow these safety precautions may result in severe injury
to yourself and others.
Always check the transmitter and receiver battery voltage to ensure
they have enough remaining capacity to complete the flight.
The GY440 requires 3-5 seconds to initialize when the power is turned
on. Do not move the helicopter and do not move the rudder stick during
this initialization or the gyro may not initialize properly. Once the initializa-
tion process has been completed the rudder servo will move (a little) sev-
eral times indicating that the GY440 is now ready for flight.
Always ensure that there is some slack in the gyro cables to help
maximize performance. Always use the supplied gyro mounting pads to
attach the gyro to the helicopter mechanics. Do not use a strap that en-
compasses the GY440 sensor. This may affect the overall performance of
the gyro.
If you are switching between NORMAL mode and AVCS mode in flight,
please keep in mind that you must have the gyro re-learn the center posi-
tion after making a trim change within the transmitter. To memorize the
new center position simply flip the gain switch on the transmitter three
times between NORMAL mode and AVCS mode (NORMAL
→
AVCS
→
N
ORMAL
→
AVCS
→
NORMAL
→
AVCS) within one second. The servo will
center indicating that the new center position has been memorized.
Be sure to use a digital servo. Use only digital servos with the GY440.
Using the GY440 with an analog servo will damage the servo.
Always check the direction of operation of the servos. If you attempt to
fly the model when a servo operates in the wrong direction, the fuselage
will spin in a fixed direction and enter an extremely dangerous state.
Do not drop the GY440 onto a hard surface or subject the GY440 to a
strong shock as this may damage the sensor.
When using the GY440 in the AVCS mode, set revolution mixing to
OFF.
Do not place gyro near heating equipment (engine, motor, ESC, bat-
tery, servo, etc.). Always allow the gyro to adjust to the surrounding envi-
ronmental temperature before flight. A large temperature change during
use will cause drift and other operational issues.
Rudder servo
※Only digital servo
Gyro gain CH(Receiver)←connect→Port2(GY440)
Remote gain effective. Trimmer(GY440) becomes LIMIT.
Gyro gain CH(Receiver)←It does not connect→Port2(GY440)
Remote gain is invalid. Trimmer(GY440) becomes GAIN.
Extension Cord:（Black）
Extension cord:（Red）
GY440
Port 3
Port 1
Rudder CH
Gyro gain CH
Port 2
Receiver
S.BUS Receiver
S.BUS CH
Rudder --- 4CH
Gyro gain --- 5CH
GY440
Port 2 is not connected.
In S.BUS connection, the port 2
is not connected.
Remote gain is still effective.
S.BUS/S.BUS 2 port
Rudder servo
※Only digital servo
Extension cord:（Black）
Port 3
Port 1
Main rotor shaft
90°
Gyro mounted to the helicopter
GY440
Sensor tape
LIMIT
GAIN
LIMIT
GAIN
Install the sensor so that the bottom of the
gyro is perpendicular to the main rotor shaft
axial direction. Offset of this axis will also re-
act in the roll and pitch directions.
$VVKRZQLQD¿JXUHWKHGLUHF-
tion which sticks GY440 is free.
• No part of this manual may be reproduced in any form without
prior permission.
• The contents of this manual are subject to change without prior
notice.
• Futaba is not liable for any potential damage (accidental or oth-
erwise) that may occur after installation.
Before using your new gyro, please read this manual thoroughly
and use the gyro properly and safely. After reading this manual,
store it in a safe place.
Thank you for purchasing a GY440
gyro, a rate gyro for RC helicopters.
GY440 is a lightweight micro gyro
developed for RC helicopter rudder
(yaw axis) control. It can be used with
mininum setup and includes an S.BUS/
S.BUS2 port.
GY440 Ratings:
(Integrated sensor type rate gyro)
• Gyro sensor: MEMS vibrating structure gyro
• Operating voltage: DC4.0V to 8.4V
• Current drain: 30mA (excluding a servo)
• Operating temperature range: -10ºC to +45ºC
• Dimensions: 20.5 x 20.5 x 11.0mm (except protrusion)
• Weight: 3.7g
• Functions: Sensitivity trimmer. LED monitor. Servo
VHOHFWLRQX6X66%866%86FRQQHFWLRQ
*Oil on the sensor bottom and the part in-
stalled to the frame can be wiped off with
cleaner, etc.
GY440 installation precautions
· Always use the accessory sensor tape to
install the GY440. Install the GY440 the
center of the sensor tape.
· Depending on the vibration from the heli-
copter, the sponge may tear near the cor-
ners of the sensor tape. If the helicopter is
flown in this state, vibrations will not be
sufficiently absorbed and the sensor may
fall off. Before flight, always check the sen-
sor installation state. If the sponge is torn,
replace it.
Make the initial linkage connections in the NORMAL mode.
In this case, make adjustments mechanically and make mini-
mum trimmer adjustments at the transmitter.
In the NORMAL mode, make the following linkage checks:
ā,QWKH UXGGHUQHXWUDOSRVLWLRQ FRQQHFWWKHOLQNDJH DWWKH SRVLWLRQ DW
which the servo horn and control wire are perpendicular.
Perpendicular
Control wire
Set the servo horn length based on
the helicopter manufacturer's instruc-
tions.
Move the rudder stick to the right and left and check the di-
rection of operation of the tail rotor. If the tail rotor turns in
the wrong direction, reverse the direction with the transmitter
reverse function.
1M23N30602
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba GY440 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba GY440 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info