30012
2
Zoom out
Zoom in
Previous page
1/6
Next page
TRANSMITTER FP-T5NLH CONTROLS
Fig. 1 shows the name of each part of the transmitter.
Memorize the position and operation of each
switch and control.
Transmitter crystal
Idle up trimmer
Antenna
Pitch control trimming knob (CH5)
Throttle hold trimmer
Carrying bar
Throttle
hold switch
Revolution mixing down knob
Revolution mixing up knob
Idle up switch
Level meter
Throttle trim
lever
Rudder trim
lever
Throttle
Rudder
Servo reversing
switches
Power
switch
Neck strap bracket
Charging jack
Aileron trim lever
Throttle trim
lever s/ATL
Aileron
Elevator
Nonslip
adjustable lever head
MODE II
Battery cover
Fig.1
Transmitter
NiCad battery
NT-8LP
Aileron AST
trimmer
Elevator AST
trimmer
In the following descriptions, all the servo reversing switches
are assumed to be in the normal position. When they are in the
reverse position, operation is the opposite of that described.
Mixing circuit is used for cancelling the torque reaction of the main
rotor. The controls for set the minimum mixing necessary for heli-
copter flight.
Aileron Aileron operation
Elevator Elevator operation
Throttle Throttle operation
Rudder Rudder operation
Pitch control trimming knob (CH5)
Pitch control trimming knob. Approximately 30% of the full throw
of the servo can be adjusted and set. Normally, it is set for the best
pitch during flight.
Aileron trim lever Aileron trimmer.
Elevator trim lever Elevator trimmer.
Throttle trim lever w/ATL
Adjustable throttle limiter
type
trim
lever.
Operates
as
a trim lever only when the
throttle stick is at the
SLOW side as shown in
Fig.
2.
SLOW
Servo throw by
throttle trimmer
As the HIGH side does not
change even when the trim
is altered, it is extremely
convenient when connect-
ing the linkage, etc.
(30% of full throw;
Throttle servo
Rudder trim lever Rudder trimmer.
Revolution mixing down side ratchet
knob
(down
side
knob)
Revolution mixing up side ratchet knob (up side knob)
Knob which adjusts the throttle rudder mixing amount. Approxi-
mately 70% mixing
at
the up and
down
sides.
Exclusively
for
rotor
clockwise rotation.
The LOW side mixing amount from mid throttle (hovering point)
position is adjusted and set with the down side knob
The HIGH side mixing amount from mid throttle (hovering point)
position is adjusted and set with the up side knob
The amount of the
revolution mixing
up side knob 11
and down side
knob 10 begins
individually set
from the neutral
position of the
HIGH
Fig. 2
Servo throw
by throttle
stick
throttle stick
Mixing is adjusted and
set over this range with
the revolution mixing
up side knob 11 .
.Throttle stick neutral
position
Mixing is adjusted and
set over this range with
the revolution mixing
down
side
knob®.
Throttle hold switch
When this switch is ON, the throttle servo stops at the position set
with trimmer and only the pitch servo is controlled toy the
throttle stick. It is used for auto rotation landings. When this, switch
is OFF, the throttle and pitch servos are mixed. The switch is turn-
ed on when pulled forward.
Throttle hold trimmer
Trimmer which
sets
the
throttle
servo stop
position
when the
throt-
tle hold switch is ON. Full travel setting is possible.
Idle up switch
When this switch is pulled forward, it is turned on and the position
set with the idle up trimmer on the back of the transmitter
becomes the maximum slow position of the throttle servo. When
this switch is set to OFF, the normal slow position of the stick be-
comes the maximum slow position of the throttle servo.
Power switch The upper position is ON.
Level meter This level meter indicates the transmitter battery voltage
Neck strap bracket Bracket for the neck strap (optional).
Antenna
Strong telescoping antenna. Extend it to its full length when using
the transmitter.
Handle Use this bar to carry the transmitter.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Futaba FP5NLH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Futaba FP5NLH in the language / languages: English as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info