63109
1
Zoom out
Zoom in
Previous page
1/2
Next page
ENCOUNTER
ACTIVE ENCLOSURES
EN-AT1100, EN-AT1120
Disclaimer
The provided self adhesive feet are intended for initial site placement only, and are not to be considered a suitable method
of securing the Active Enclosure. Always ensure the Active Enclosure is securely attached, to avoid movement.
FUSION accepts no responsibility for damage or injury in relation to inappropriate securing of this product
Product Specifications
Control Descriptions
LEVEL
This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If the sound becomes
distorted reduce the level.
LOW PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce. This should be adjusted to
blend with your main speakers. Typically, this will be set to around 100Hz (approximately the central position of the control knob).
BASS
This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound becomes distorted, reduce
the amount of boost.
REMOTE LEVEL CONTROLLER
When connected, this allows further control over the level from a remote location, using the supplied lead.
Installation
Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near
gas tanks, fuel lines, hydraulic lines or electrical wiring.
DO NOT mount the Encounter Active Enclosure in such a way as to pinch or damage the wires.
Make sure everything is firmly connected, before attaching the +12V wire. Make sure the +12V wire is fused as close as possible
to the battery. ALWAYS use a fuse with the recommended rating.
Two types of self-adhesive feet are included in the packaging. The rubber feet are to protect the bottom of the enclosure, or the
surface it is mounted to. There are four feet, which correspond to four indentations (feet and indentations are the same shape) in
the bottom of the enclosure end plates. Peel off the paper covering the rubber feet, and adhere to the indentations.
There are also four Velcro feet (both hook and eye parts, both with self-adhesive properties) included. These are for assisting
in fixing the location of the enclosure. Peel off the paper covering and adhere one part to the indentations in the enclosure end
plates, and the matching part to the mounting surface. Always clean the surfaces before applying the adhesive part
EN-AT1100 EN-AT1120
Max Power Rating 300 Watts 360 Watts
Frequency Repsonse 35Hz - 250Hz 30Hz - 250Hz
Bass Boost (Variable) 0 / + 18dB 0 / + 18dB
Low Pass Filter (Variable)
40Hz - 250Hz 40Hz - 250Hz
Tuning Bass Reflex Bass Reflex
Woofer Size 10” 12”
Fuse 15 Amp 15 Amp
Tube Dimensions 550mm x 306mm x 306mm
21 11/16” x 12 1/16” x 12 1/16”
590mm x 365mm x 365mm
23 1/4” x 14 3/8” x 14 3/8”
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fusion EN-AT1120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fusion EN-AT1120 in the language / languages: English as an attachment in your email.

The manual is 0,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info