101497
60
Zoom out
Zoom in
Previous page
1/67
Next page
119118
Troubleshooting
e If you think the camera is faulty, check the following once more
Troubleshooting Possible causes Solutions
Frame erase does not
erase the frame.
i DPOF settings are specified for some
frames.
i Some frames may be protected.
i Cancel the DPOF settings and try again
(P.67).
i Remove the protection.
The ERASE ALL function
does not erase all the frames.
When the camera is connected
to a personal computer (PC),
the shot image appears on the
camera’s LCD monitor.
i The special FinePix F402 USB cable is not
properly connected to the computer or
camera.
i The PC is not switched on.
i Set up the camera and the special FinePix
F402 USB cable correctly.
i Switch the PC on.
Nothing happens when I
use the camera switches.
i Camera malfunction.
i The battery is exhausted.
i Briefly remove the battery or disconnect the AC
power adapter. Then reload the battery or
reconnect the AC power adapter and try again.
i Load a new fully charged battery.
The camera no longer
works correctly.
The camera has suffered an unforeseen
problem.
Briefly remove the battery or disconnect the
AC power adapter. Then reload the battery or
reconnect the AC power adapter and try again.
There is speckling on the
image.
The shot was taken with a slow shutter speed (long
exposure) in a high-temperature environment.
This is a characteristic of CCDs and does not
indicate a camera fault.
No photograph is taken
when the shutter button is
pressed.
i The xD-Picture Card is damaged.
i The Auto Power Off function has switched
the camera off.
i The battery is exhausted.
i Load a new xD-Picture Card.
i Switch the camera on.
i Load a new fully charged battery.
Troubleshooting Possible causes Solutions
Can only select “Suppressed
Flash” flash mode.
Continuous shooting is selected. Set continuous shooting to OFF.
Can’t use the flash to take
pictures.
i The shutter button was pressed while the
flash was charging.
i The Suppressed Flash mode is selected.
i Wait until charging is completed before
pressing the shutter button.
i Set the flash mode to Auto, Red-eye
Reduction or Forced Flash (The flash cannot
be used in some modes).
Can only select the “1
resolution setting.
The sensitivity is set to 800 or 1600 (high-
sensitivity photography) in the Photography menu.
In the Photography menu, set the sensitivity
to 400 or less.
The photographed image
is dark even though I used
the flash.
i The subject is too far away.
i Your finger was covering the flash/flash
control sensor.
i Move to within the effective flash range
before taking the shot.
i Hold the camera correctly.
The image is blurred.
i The lens is dirty.
i You photographed scenery with Macro mode
selected.
i You took a close-up shot without selecting
Macro mode.
i You are shooting a subject that is not suited
to autofocusing.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the shot.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fujifilm Finepix F 402 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fujifilm Finepix F 402 in the language / languages: English as an attachment in your email.

The manual is 2,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info