787196
5
Zoom out
Zoom in
Previous page
1/7
Next page
Infralu
5
EN
Installation and operating instructions
Positioning
The heaters must be placed so that they
cover the area to be heated, see fig. 1. The
normal mounting height is 2–3 metres above
the ground/floor. A rule of thumb for infrared
heaters is that 600–800 W/m² increases the
experienced temperature by about 10 °C. The
output demand can be reduced if the area to
be heated is protected. If the area only has a
roof, at least 800 W/m² should be installed.
600 W/m² is sufficient if the area has three
walls. For enclosed areas, the output demand
must be calculated. Optimum comfort is
achieved if the heat is distributed from at
least two directions.
Mounting
IHAL is installed horizontally on walls
with supplied bracket. For other mounting
alternatives, e.g. in the ceiling, on a floor
stand, under a parasol or awning, see
accessories. For minimum distances, see
diagrams on introductory pages.
Connection
IHAL is equipped with a 1.9 metre cord with
plug for connection to an earthed outlet
socket. The connection cord must not rest
against the unit as the surface becomes hot or
can be hit by thermal radiation. Contact an
electrician if the cord needs to be changed.
General Instructions
Read these instructions carefully before
installation and use. Keep this manual for
future reference.
The product may only be used as set out in
the assembly and operating instructions. The
guarantee is only valid if the product is used
in the manner intended and in accordance
with the instructions.
Application
Infralu is a compact, user friendly halogen
infrared heater in polished aluminum for
outdoor use. It is equipped with a gold
infrared tube and cord with plug for easy
installation.
Protection class: IP67.
Start-up
When the unit is used for the first time or
after a long period of disuse, smoke or odour
may result from dust or dirt that has collected
on the element. This is completely normal
and disappears after a short time.
Replacing the lamp
The heat lamp is of the highest quality and
unless it is subjected to mechanical strains in
the form of vibrations and impact it will last
for a long time. The service life is dependent
on the ambient temperature and how the
heater is installed. When the heater is
installed freely and outdoors the temperature
will be low and the life of the lamp longer.
The lamp must be replaced by an installer
or other skilled person.
1. Disconnect the power supply.
2. Wait until the unit is cold.
3. Check that the replacement lamp has the
correct output and voltage.
4. Fit the new lamp. Note do not touch the
lamp with your fingers, wear gloves or the
like.
5. The protective tube must be refitted to the
cables, so that the cables are not damaged
when the grille is fitted.
6. Reassemble the unit again.
As the halogen lamp has a high starting
current the wall socket should be fuse
protected by a slow burn fuse.
In the event of uncertainty contact an
electrician.
Maintenance
The power supply to the unit must be
disconnected during all service, repair and
maintenance work.
The unit has no moving parts so the
maintenance requirement is small, but it
must be kept clean and free from dust and
dirt. If the reflector is not clean the thermal
radiation from the unit will decrease and the
heater will become hotter. A large amount of
dirt can cause overheating.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frico IHAL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frico IHAL in the language / languages: English as an attachment in your email.

The manual is 0.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Frico IHAL

Frico IHAL User Manual - German - 9 pages

Frico IHAL User Manual - Dutch - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info