628407
46
Zoom out
Zoom in
Previous page
1/48
Next page
46
Lines under Test
The CE2N-416 control unit allows you to test the lines without it activating the alarm outputs and the
tone signals from the keypads.
Under the test mode, the line is activated according to the programmed modes (for example, a
delayed line keeps the input/output time, even when it is being tested).
An alarm on lines being tested is signalled on the keypad display, on the red LED of the keypad and
on the key reader. The alarm is recorded in the historic log.
A line being tested generates a self-protection alarm (if the line is configured as single or double
balancing).
ATTENTION: if a line is excluded manually or it is being TESTED and the system is COMPLETELY
ARMED, the CHBUS reader will show the LED permanently green (all armed), the keypad will display
the zone/s excluded even if the system is completely armed and will display the words “CENTRALE
PARTE INSERITA”. The event log will record the zone exclusion and, if the system is completely
armed with one excluded zone, the words “TOTAL ACTIVATION” will be displayed.
Output function test
The CE2N-416 control unit allows the testing of all alarm outputs on the card by activating each of
them for about 3 seconds.
Walk test
The control unit allows you to quickly and efficiently check the correct operation of the sensors and
modules.
Place the control unit in “line walk test” mode and activate the sensors that you want to control.
The keypad buzzer will generate a tone every time the sensor is activated and the activation will be
recorded on the display.
Walk test Tamper
The control unit allows you to quickly and efficiently check the proper operation of the sensor self-
protections. Place the control unit in “walk test tamper” mode and open the cases of the sensors
that you want to control. The keypad buzzer will generate a tone every time that the contact is
activated and the activation will be recorded on the display.
Channel test
The control unit allows the test of the phone alarm channels and the correct dispatch of vocal and/
or digital messages to a specific number.
The call is sent without generating an effective alarm.
DTMF reception test
The control unit can test the reception of the DTMF tones.
This test allows you to understand if the CE2N-416 control unit recognizes the DTMF tones sent by
the phone line from a phone.
Choose an active channel and an associated phone number; press V to call.
• Answertheincomingcall
• NOmessagewillbeheard
• Pressthevariousdigits1,2,3,4,5,6,7,8,9,0,*,#fromthephonekeypad
• FromthedisplayoftheT8Nand/orT8N-Lightkeypads,thesamegureswhichare
pressed on the phone will appear in the same sequence.
If the numbers don’t appear, modify the sensitivity of the telephone in the menu
Dialler Control unit phone options reception gain
If the problem is not solved, check the connection and/or check the signal quality
of the incoming phone line.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fracarro CE2N-416 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fracarro CE2N-416 in the language / languages: English as an attachment in your email.

The manual is 4,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info