662898
4
Zoom out
Zoom in
Previous page
1/8
Next page
3
Assembly Instructions
Safety Guard Assembly (A), (B) & (C)
If you have a Multi Trim 200 your safety guard
will be fitted with a wire guard as shown in figure
J2.
1. Align the arrow on the top of the safety guard (A1)
with the arrow on the side of the trimmer (A2).
2. Locate the safety guard (A3) over the cutting head
(A4). Ensure the nylon line is fed through the hole in
the safety guard as illustrated in fig A.
Please note: Depending on which model you
have purchased, your trimmer may be fitted with
one line or two lines.
3. Push into location and turn safety guard in the direc-
tion illustrated in Fig B, until a click is heard and the
safety guard is securely locked in position.
ENSURE THE SAFETY GUARD IS SECURELY IN
PLACE BY ATTEMPTING TO TWIST GUARD.
See fig C.
Steady Handle Assembly (D), (E) & (F)
1. Insert the nut into the handle knob. (if applicable).
2. Attach steady handle to product using bolt and han-
dle knob as shown in Fig D.
3. To adjust steady handle to new position, loosen han-
dle knob as shown in Fig E. and move handle to one
of the three positions as shown in Fig F.
4. Re-tighten handle knob
Height Adjustment (if fitted)
If your trimmer is fitted with Height Adjust, follow
the procedure below.
1. Loosen the height adjust knob. (fig G)
2. Adjust length of the handle to the most comfortable
operating position (fig H).
3. Re-tighten the height adjust knob.
A
B C
4
2
3
1
D
F
E
bolt
handle
knob
G H
height
adjust
knob
If you have a Multi Trim 200, it will be fitted with a
wire guard as shown in figure J2.
Please note: Depending on which model you have
purchased, your trimmer may be fitted with one line
or two lines.
Auto Line Feed System
How the automatic line feed works (J)
1. When initially switching on the trimmer, a small
length of line is fed out.
2. A ‘clattering’ noise will be heard when the nylon line
hits the line cutter. DO NOT BE ALARMED this is
quite normal. After approximately 5 seconds the
line will be cut to the correct length and the noise will
reduce as the motor reaches full speed.
Make sure the motor is up to full speed before
trimming or edging.
3. If the noise of the nylon line being cut cannot be
heard, more line will need to be fed out.
4. To feed more line, it is first necessary to to allow the
motor to stop completely, then re-start, allowing the
motor to reach full speed.
5. Repeat step 4. until you hear the line hitting against the
cutter. (Do not repeat this procedure more than 6 times)
6. If problems are experienced with the automatic line
feed refer to Fault Finding Chart.
J1
J2
Multi Trim 200 only
line
cutter
line
cutter
wire
guard
nut (if applicable)
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Flymo MET 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Flymo MET 200 in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info