775834
60
Zoom out
Zoom in
Previous page
1/62
Next page
1773/1775/1777
Users Manual
54
Transients. Transient overvoltages are either non-oscillatory (impulsive) or oscillatory signals
on mains caused by lightning strikes, switching of heavy loads, such as motors, welders, power
factor correction banks, or switching of overcurrent protection devices.
Transient overvoltage can cause damage to the insulation of motors, transformers, and
electronic equipment. Depending on the overvoltage category, peak values can occur, see
Table 1 4 .
Measurement modes:
PQ Meter
PQ Logger
Parameters to configure:
Trigger on/off
Sample rate 1 MS/s or 20 MS/s
On the Fluke 1777, use 1 MS/s if the subsequent waveform after the event up to 0.5 s is of
interest.
Note
The use of 1 MS/s impacts the accuracy of the peak measurement.
Table 14. Transient Voltages
Voltage Line-to-Neutral and Line-to-Ground >100
150V
>150V
300V
>300V
600V
>600V
1000V
CAT II Single-phase receptacle
connected loads
Appliance, portable tools, and other
household and similar loads
Outlet and long branch circuits
Outlets at more than 10 meters
(30 feet) from CAT III source
Outlets at more that 20 meters
(60 feet) from CAT IV source
1500 V 2500 V 4000 V 6000 V
CAT III
Three-phase distribution,
including single-phase
commercial lighting
Equipment in fixed installations, such
as switchgear and polyphase motors
Bus and feeder in industrial plants
Feeders and short branch circuits,
distribution panel devices
Lighting systems in larger buildings
Appliance outlets with short
connections to service entrance
2500 V 4000 V 6000 V 8000 V
CAT IV
Three-phase at utility
connection, any outdoor
conductors
Refers to the “origin of installation,”
for example, where low-voltage
connection is made to utility power
Electricity meters, primary
overcurrent protection equipment
Outside and service entrance, service
drop from pole to building, run
between meter and panel
Overhead line to detached building,
underground line to well pump
4000 V 6000 V 8000 V
12 000 V
(not
supported)
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 1773 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 1773 in the language / languages: English as an attachment in your email.

The manual is 3.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info