Manual Florabest FBS 43 B2 - IAN 97786 (page 51 of 56) (English, German, Dutch, French, Italian)

576716

Zoom out

Zoom in

1/56

FBS 43 B2

Installing/replacing the line spool

■ Install/replace the line spool as displayed in ﬁ gure 7c.

■ Locate the drive shaft drill hole , align it with the underlying groove

and lock it in place with the hexagonal key

included, now screw the

line spool

onto the thread.

NOTE! Left-hand thread!

Putting on the shoulder strap

NOTE

■

The following adjustments can be made to make sure that you can

work without becoming fatigued. The settings may vary depending

on your body size.

■ Before starting work, adjust the shoulder strap and the handle to your

body size.

■ Balance the petrol-driven scythe with the installed cutting tool so that

the cutting tool hovers just above the ground without touching the

petrol-driven scythe with your hands.

1.) Put on the shoulder strap and connect the two shoulder strap parts until

they lock (see ﬁ g. 8a - 8b).

2.) Pull on the shoulder strap, as displayed in 8c, to move the shoulder

strap to the centre of your body and adjust the upper body girth ac-

cordingly.

3.) Now pull on the two shoulder straps, as displayed in ﬁ gure 8d, to

tighten them.

4.) To set the correct position of the petrol-driven scythe on the shoulder

strap, pull on the belt as displayed in ﬁ gure 8e.

5.) Hook in the carabiner

(see ﬁ g. 8f - 8h) and secure it with the red

strap

on the quick release mechanism.

6.) Now pick up the petrol-driven scythe and hang it in carabiner

using

holder

as shown in ﬁ gure 8i. The bracket can also be released

and shifted using a screw

in order to set the best possible position of

the petrol-driven scythe.

7.) The guide handle

can now be adjusted using 2 screws on the

underside to set the perfect position of the guide handle

Setting the cutting height

■ Put on the shoulder strap as displayed in ﬁ gure 8a - 8c.

■ Hook the device into the shoulder strap (see ﬁ g. 8d).

■ Set the ideal working and cutting position using the various strap adjust-

ers on the shoulder strap (see ﬁ g. 8e).

■ Perform a few circular movements without starting the engine in order to

ﬁ nd the ideal shoulder strap length (see ﬁ g. 9a).

■ The shoulder strap is equipped with a quick release mechanism. Pull on

the red strap if you have to release the device quickly (see ﬁ g. 8k).

IMPORTANT!

■ Always use the shoulder strap when working with the device.

Put the strap on as soon as you have started the engine and it is

idling. Turn oﬀ the engine before removing the shoulder strap.

Fuel and oil

IMPORTANT!

■ Do not use a fuel mix that has been stored for over 90 days.

Recommended fuels:

■ Only use a mixture of unleaded petrol and special 2-stroke engine oil.

Mix the fuel mixture in accordance with the fuel mix table.

■ Pour the correct amount of petrol and 2-stroke oil into the enclosed

mixing canister (see fuel mix table). Then shake the canister well.

Fuel mix table

Mixing process: 40 parts petrol to 1 part oil

Petrol 2-stroke oil

1 litre 25 ml

5 litre 125 ml

Operation

IMPORTANT!

■ Please pay attention to the statutory provisions in the noise protection

regulations.

Before starting the device, check for:

■ Tightness of the fuel system.

■ Flawless condition and completeness of the protective equipment and

cutting equipment.

■ Firm position of all screw connections.

■ Smooth running of all moving parts.

Starting when the engine is cold

IMPORTANT!

■ Never allow the starter line to snap back. This may result in damage.

1. Fill the tank. (see also "Fuel and oil" section).

2.) Press the fuel pump

(primer) 6 times.

3.) Turn the on/oﬀ switch

to "I".

4.) Set the choke lever

to " ".

5.) Hold the device ﬁ rmly and pull out the starter pull cord

to the point

of ﬁ rst resistance. Now quickly pull the starter pull cord

. The device

starts.

6.) If the engine does not start, repeat steps 4-5.

7.) Once the engine has started, press the throttle control

to release the

auto choke.

If the engine does not start after several attempts, read the "Troubleshooting

guide" section.

IMPORTANT!

■ Always pull the starter pull cord out straight. Hold the starter pull

cord handle ﬁ rmly

when the starter pull cord retracts.

Never allow the starter pull cord to spring back.

NOTE

■

At very high ambient temperatures it is possible that even a cold

engine has to be started without using the choke!

Starting when the engine is hot

(The device has been turned oﬀ for less than 15-20 minutes)

1.) Turn the on/oﬀ switch

to "I".

2.) Set the choke lever

to " ".

3.) Hold the device ﬁ rmly and pull out the starter pull cord

to the point

of ﬁ rst resistance. Now quickly pull the starter pull cord

. The device

should start after 1-2 pulls. If the device has not started after 6 pulls,

repeat steps 1-7 under "Starting when the engine is cold".

IB_97786_FBS43B2_LB1.indb 46 03.07.14 15:16

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBS 43 B2 - IAN 97786 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 1,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Florabest FBS 43 B2 - IAN 97786 Manual

Product: