456443
18
Zoom out
Zoom in
Previous page
1/20
Next page
40069 Zola Predosa (BO) - ITALY
info@finicompressors.it
- GB -
6.1 CONTROLS AND MAINTENANCE
The maintenance operations must be worked out by qualified personnel.
Before any intervention, Ensure that:
no part of the machine is powered and that it cannot be connected to the mains supply.
no part of the machine is under pressure and that it cannot be connected to the compressed
air system.
Before attempting any maintenance operation on the dryer, switch it off and wait at least 30
minutes. During operation the copper piping connecting the compressor to the condenser can
reach dangerous temperature able to burn the skin.
DAILY
Verify that the DewPoint temperature displayed on the DTT11 electronic instruments is correct.
Check the proper operation of the condensate drain systems.
Verify the condenser for cleanliness.
EVERY 100 HOURS
With an air jet (Max. 2 bars) blowing from inside towards outside clean the condenser; repeat
this operation blowing in the opposite way; be careful not to damage the aluminium blades of the
cooling package.
Close the manual condensate drain valve, unscrew the mechanical strainer and clean it with
compressed air and a brush. Reinstall the strainer properly tight, and then open the manual valve.
At the end, check the operation of the machine.
EVERY 3000 HOURS
Verify for tightness all the screws of the electric system and that all the “Faston” type
connections are in their proper position.
Check the conditions of the condensate drain flexible hoses, and replace if necessary.
At the end, check the operation of the machine.
FS 018 INLET FILTER (1 MICRON)
EVERY 3000 HOURS
Depressurize the dryer.
Disconnect the filter from the relevant condensate drainage
circuit.
Unscrew the clogged cartridge.
Clean accurately the filter head, particularly the sealing surfaces.
Lubricate the tightness gasket of the new cartridge. Use
multipurpose grease (SILICON FREE).
Screw the new cartridge firmly by hand to the head of the filter.
Connect the relevant condensate drainage circuit.
Pressurize the plant and check for air leakage.
Screw Unscrew
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finicompressors Artic 134-EVO luchtdroger at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finicompressors Artic 134-EVO luchtdroger in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info