574902
14
Zoom out
Zoom in
Previous page
1/77
Next page
14
TXS
GB
Side of the belt clip
[2-1]
can be replaced when
battery pack is removed.
6.2 Charging the battery pack [3]
The LED
[3-1]
on the charger indicates the respec-
tive operating status of the charger.
7 Settings
7.1 Changing direction of rotation [1-5]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rotation
7.2 Changing gear [1-4]
Gear switch forwards (digit 1 visible) = 1st gear
Gear switch to rear (digit 2 visible) = 2nd gear
7.3 Adjust torque [1-2]
The marking
[1-3]
shows the selected position.
Drilling
Marking shows the drill symbol
[1-1]
= Maximum
torque.
Fastening
Torque corresponding to setting:
Position 1 = low torque
Position 12 = high torque
8 Tool holder, attachments
The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
8.1 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CENTRO-
TEC tool chucks.
8.2 Chuck BF-FX10 [5]
For clamping drill bits and bits with max. shaft di-
ameter of 10 mm.
Clamp tool centrally in the chuck.
8.3 Angle attachment XS-AS [6]
(accessories) Drilling and screwdriving at right an-
gle to power tool.
You can engage the angle attachment in 16 dif-
ferent angle settings.
8.4 Tool holder in the drill spindle [7]
Bits can be inserted directly into the hexagon sock-
et holder of the drill spindle.
9 Working with the power tool
9.1 On/Off switch [1-6]
Press = ON, release = OFF
LED yellow - lit continuously
Charger is ready to use.
LED green - flashing quickly
Battery pack is charged to maxi-
mum capacity.
LED green - flashing slowly
Battery pack is charged to 80%
and with reduced current.
LED green - lit continuously
Battery pack is charged.
LED red - flashing
General fault indicator, e.g.
incomplete contact, short circuit,
defective battery pack, etc.
LED red - lit continuously
Battery temperature is outside
permissible limit values (0 °C to
55 °C).
CAUTION
Risk of injury
Always switch off the power tool before adjusting
settings!
WARNING
Risk of injury
Always disconnect the battery pack before per-
forming any type of work on the machine!
CAUTION
Hot and sharp tools
Risk of injury
Do not use insert tools that are blunt or defec-
tive.
Wear protective gloves.
WARNING
Risk of injury
Always secure the workpiece in such a manner
that it cannot move while being machined.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TXS Li 2.6-Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TXS Li 2.6-Plus in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 21,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info