427184
2
Zoom out
Zoom in
Previous page
1/4
Next page
9
Edge router
Technical data OFK 500 Q
Wattage 450 W
Drive shaft rotating speed 28,000 rpm
Max. Diameter of milling tool 27 mm
Weight 1.5 kg
Degree of protection
/ II
The specifi ed illustrations can be found at the
beginning of the operating instructions.
Symbols
Warning of general danger
Wear ear protection!
Read the Operating Instructions/Notes!
1 Intended use
The OFK 500 Q is intended for fl ush trimming and
profi ling of wood, plastic and similar materials.
The user is liable for damage and injury
resulting from incorrect usage!
2 Safety instructions
2.1 General Safety
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock, fi re
and/or serious injury.
Save all warnings and instructions for future
reference.
The term „power tool“ in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
2.2 Tool-specifi c safety rules
- Hold the power tool by insulated gripping
surfaces only, because the cutter may contact
its own cord. Cutting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
- Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the
body leaves it unstable and may lead to loss of
control.
- Do not operate the machine unless the guiding
table (1.5) and the safety hood (1.2) have been
correctly installed.
- Do not operate the machine unless the setting
ring gauge is locked (see chapter 4.2).
- Only use milling tools that are EN 847 certi-
ed for rotating speeds of at least 30.000 rpm.
Tools that are cracked or misshapen must not
be used.
- Ensure that the milling tool is fi rmly seated and
check that it runs smoothly.
- Only use original Festool accessories.
2.3 Safety instructions Cutter
a) Technical data
See imprint on tool.
Tool manufactured to comply with EN 847-1.
b) Correct use
Type of feed: MAN (manual feed).
Speed: Do not exceed the maximum speed speci-
ed on the tool and/or keep to the speed range.
Materials: Wood, plastic.
Warning: The operator is liable for damages and
accidents caused by incorrect use!
c) Safety instructions
Pay attention to the safety instructions included
with your tool.
Pay attention to the safety regulations applicable
on your country.
Do not use tools with noticeable cracks, blunt or
damaged cutting edges ---> danger to live!
The clamping surfaces must be free of dirt,
grease, oil and water.
Clamp the tool so that it cannot come loose dur-
ing work.
Insert the router into the clamping collet as far
as possible or as far as the mark on the router
shank.
Only mill in the opposite direction of rotation of
the tool (counter-rotation).
c) Maintenance and care
Use only original Festool spare parts.
Repairs and grinding work may only be carried out
by Festool service centres or qualifi ed experts.
Do not alter the construction of the tool.
Clean tool regularly and remove all resin (use
detergents with a pH value between 4.5 and 8).
Blunt cutting edges can be re-ground to a mini-
mum cutting edge thickness of 1 mm on the
face.
2.4 Noise and vibration information
The typical values determined in accordance with
EN 60745 are:
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ofk 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ofk 500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info